Yali Kuang

Yali Kuang


Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 December 2015 in Applied Biochemistry and Biotechnology
Verified
Journal Article
Closed access
PDF file
GHGuanhua Huang
Guanhua Huang
FCFeng Chen
Feng Chen
YKYali Kuang
Yali Kuang
HHHuan He
Huan He
AQAn Qin
An Qin

5 August 2016 in Environmental Progress & Sustainable Energy
Verified
Journal Article
Closed access
PDF file
GHGuanhua Huang
Guanhua Huang
TLTao Li
Tao Li
FCFeng Chen
Feng Chen
HHHuan He
Huan He
YKYali Kuang
Yali Kuang

30 September 2009 in Procedia Earth and Planetary Science
Verified
Journal Article
Open access
YKYali Kuang
Yali Kuang
ZJZhang Jun
Zhang Jun
ZHZhang Hai-Yang
Zhang Hai-Yang
GJGe Jun
Ge Jun
To meet the needs of the jigging process control, attempt to combine the studying on jigging mechanism with the operating and detecting parameters so as to use them in practical producing control. On the basis of studying the motion characteristic of water in jig, the motion of particles with different size and density was researched. A laboratorial model jig and a high-speed dynamic analysis meter were used and 60 group conditions were designed in experiment. The motion rule and curves were gained through analyzing the huge amount of data and pictures with the high-speed dynamic analysis meter. The conclusion is that the characteristic of the position curve of the particles is similar with the typical damped vibration. Then the motion differential equation of the particles was educed imitating the damped vibration and the solution equations were gained. In the equations the motion parameters of the particles in jig, such as velocity, acceleration, force etc. are in a direct proportion to the air pressure, and have a definite non-linear relationship with the jigging cycle, thickness, mobility of the jig bed, mass and size of the particles and so on. The equations might be used directly in control process of jig.

13 April 2019 in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
Verified
Journal Article
Closed access
JZJun Zhang
Jun Zhang
YTYoujun Tao
Youjun Tao
YKYali Kuang
Yali Kuang
XGXiahui Gui
Xiahui Gui
ZWZhangguo Wang
Zhangguo Wang
Jigging is one of the common separation processes in coal beneficiation. The analysis of the impact of jigging operating conditions on the stratification process of the particles inside the model jig wash box has a great guiding significance for improving the performance of the equipment. The experimental results showed that different densities particles exchanging their position in vertical direction mainly occurred during the terminal stage of particle ascending motion and the initial stage of particle descending motion. During this stage, the jig bed was relatively loose, and particles in the bed were conditionally stratified according to their own characteristics (particle size, density, and shape). After the completion of particles stratification, the bed was separated into layers according to particles densities. Material with lower density stayed on top and material with higher density settled at the bottom. Within a bed layer of the same density, the bed was stratified into layers according to particle size. Small particles occupied the upper layer and large particles occupied the lower layer. Experiment of unhindered settling of different particles showed that the terminal settling velocity of large particles was significantly higher than that of small particles of the same density. The terminal settling velocity of large particles with lower density was lower than or equal to that of small particles with higher density. This illustrated that equal settling exists among particles of different densities and sizes. The stratification of materials based on their density could be achieved in a jig, which showed that hindered settling instead of equal setting ratio played a dominant role in jigging process.

19 December 2017 in International Journal of Coal Preparation and Utilization
Verified
Journal Article
Closed access
GWGuanghui Wang
Guanghui Wang
YYYuanhe Yue
Yuanhe Yue
YKYali Kuang
Yali Kuang
YSYingsong Shen
Yingsong Shen
ZLZhe Lin
Zhe Lin
This research applies the correlation between the cumulative float yields of certain density fractions and raw coal ash content, as well as the δ empirical model in Mayer washability curves, and finally establishes a prediction model of the cumulative float yields of all seven density fractions based on dynamic raw coal ash content. Test results show that the model’s prediction of cumulative yield at each density fraction is quite accurate when the density is higher than 1.4 g/cm3, with the largest forecast error less than 2%. Then, stepwise regression analysis is carried out among the cumulative float ash content of each density fraction and raw coal ash content to establish the model of the real-time cumulative ash content model of each density fraction. The prediction error is less than 1% when the density is higher than 1.4 g/cm3. The floating and sinking components prediction model is relatively precise, which plays a key role in the feedforward compensation model in the automatic control of heavy-medium density in a coal preparation plant.

3 November 2018 in Canadian Metallurgical Quarterly
Verified
Journal Article
Closed access
LJLi Ji
Li Ji
YKYali Kuang
Yali Kuang
YYYuanhe Yue
Yuanhe Yue
ZWZhangguo Wang
Zhangguo Wang
LTLi Tao
Li Tao
Optimisation studies on integrating different procedures in mining and mineral processing have an increasing popularity in recent years, and most of them focus on the mine-mill or mine-flotation integration. However, few optimisation studies on integrating mining with gravity separation are found. The gravity separation plays a vital role in coal preparation, which also makes the related integration study necessary. In this work, an optimisation study on integrating mining with gravity separation is first carried out, which contributes to proposing the optimal cut point (the density at which 50% of the feed report to underflow) for gravity separation and the coal seam mass ratio for mining. Specifically, a simplified optimisation model includes separations in dense medium cyclones, dense medium shallow grooves, and spiral separators is developed. Then the Differential Evolution algorithm is employed to obtain the solution that has the maximum economic profit. Finally, the organic efficiency is utilised to evaluate this optimisation. The validation results indicate that the developed optimisation model and the adopted algorithm are applicable. Even though it is a simplified model, it is supposed to provide a preliminary optimisation scheme for integrating mining with gravity separation.