6 January 2019 in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
This paper studied the macerals enrichment of the low-rank coal which produced by Shigetai Coal Mine, Shenhua Group. The coal sample fed to the Falcon were the product of the rod mill after 10 minutes grinding. Three factors were carried out, rotational frequency, feed rate and water pressure. The orthogonal experiment was designed to investigate the interaction between the three factors and a model was established between the factors and response values. Taking the vitrinite recovery rate as the response value, there was an interaction between the rotational frequency and the water pressure, moreover, the effect of the rotational frequency on the vitrinite recovery rate was greater than the water pressure, while, the feed rate on the vitrinite recovery rate was not significant. Taking the vitrinite enrichment ratio as the evaluation index, the Quadratic model was recommended, there was an interaction between the rotational frequency and the feed rate, moreover, the rotational frequency had better response to the vitrinite enrichment ratio than the water pressure and the feed rate. In order to optimize the experimental conditions, and the vitrinite enrichment ratio was set to 1.2, the vitrinite recovery rate was the larger the better, the optimal separation conditions obtained were the rotational frequency 30Hz, the water pressure 0.03MPa, and the feed rate 15ml/s in the laboratory.
2 April 2019 in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
The macerals effective dissociation is the precondition for the macerals enrichment. The macerals dissociation generally adopts the crushing and grinding process. Selective grinding is achieved by using the differences in mechanical properties between different macerals, and grinding equipment and grinding time are important factors affecting the degree of selective grinding. Hence, it is necessary to choose the suitable dissociation method, control the suitable dissociation time, avoid over-crushing, and then cooperate with the suitable concentration methods to achieve macerals efficient enrichment. In this paper, the low-rank coal studied was produced by Shenhua Shigetai Coal Mine. Coal sample was crushed to less than 1 mm and then was carried out for the grinding test by using the rod mill and the ball mill, respectively. In order to determine the macerals dissociation characteristics of Shenhua low-rank bituminous coal, the size distribution, density level, and macerals of the grinding products under the different grinding equipment and grinding time were analyzed. The test results show that the grinding effect of the rod mill is better than that of the ball mill under the same grinding time, and 10 min rod grinding can obtain the best macerals dissociation.
19 September 2018 in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
Jigging is one of the common methods for coal beneficiations. There are many factors affecting the jigging process, the three main factors consist of material characteristics, jig structure, and operation factors. For certain materials and jig structures, determining a reasonable operating system will guarantee good separation effect. Therefore, it is very important to research the impact of jigging operation factors on the material bed. We used a model jig test device to research the effects of the air cycle, inlet period, exhaust period, and air pressure on the material bed. Of these, the air cycle and air pressure were two key factors. The device’s optimum operation parameters: air cycle 1.3s, inlet period 16%, exhaust period 22%, expansion period 40%, and air pressure 0.004 MPa.
13 April 2019 in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
Jigging is one of the common separation processes in coal beneficiation. The analysis of the impact of jigging operating conditions on the stratification process of the particles inside the model jig wash box has a great guiding significance for improving the performance of the equipment. The experimental results showed that different densities particles exchanging their position in vertical direction mainly occurred during the terminal stage of particle ascending motion and the initial stage of particle descending motion. During this stage, the jig bed was relatively loose, and particles in the bed were conditionally stratified according to their own characteristics (particle size, density, and shape). After the completion of particles stratification, the bed was separated into layers according to particles densities. Material with lower density stayed on top and material with higher density settled at the bottom. Within a bed layer of the same density, the bed was stratified into layers according to particle size. Small particles occupied the upper layer and large particles occupied the lower layer. Experiment of unhindered settling of different particles showed that the terminal settling velocity of large particles was significantly higher than that of small particles of the same density. The terminal settling velocity of large particles with lower density was lower than or equal to that of small particles with higher density. This illustrated that equal settling exists among particles of different densities and sizes. The stratification of materials based on their density could be achieved in a jig, which showed that hindered settling instead of equal setting ratio played a dominant role in jigging process.
2 December 2025 in Mineral Processing and Extractive Metallurgy: Transactions of the Institutions of Mining and Metallurgy
China's coking coal scarcity and high clean coal prices make slime flotation economically vital, though reclaimed coal's severe oxidation poses major flotation challenges. Characterisation of Coal Slime from Xuehugou Coal Preparation Plant: coal slime has a high content of fine fractions, with the proportion of particles < 0.075 mm reaching 23.39%, and it is severely oxidised. The measured contact angle of the raw coal was only 32°, resulting in hydrophilicity and difficulties in floating. Traditional non-polar hydrocarbon collectors, such as kerosene and 2-octanol, were employed to scrub the surface of coal slime through high-intensity conditioning and then floated. Under the condition of identical clean coal ash content, the clean coal yield increased by 24.15%, and the combustible matter recovery increased by 26.65%. High-intensity conditioning at 12000 r/min for 20 min was identified as the optimal parameter set, achieving a clean coal yield of 67.38% with an ash content of 11.73%.