The spacecraft tracking telemetering and command (TT&C) system plays an essential role in celestial and terrestrial networks, requiring relative ranging and communication, particularly in satellite formation flying networks and distributed spacecraft networks. To achieve precious ranging and high-data-rate communication in a Master/Slave satellite architecture, an integrated communication-ranging system (ICRS) is introduced. ICRS is based on the inter-satellite spread spectrum ranging and spread/non-spread spectrum communication modulated by unbalanced quadrature phase shift keying (UQPSK). In both uplink and downlink, the in-phase (I) branches and the quadrature (Q) branches undertake the tasks of ranging and communication, respectively. In addition, a global navigation satellite system (GNSS) like signal is adopted in I branches for the sake of better ranging accuracy, and binary phase shift keying (BPSK) modulation is employed in Q branches for a higher data rate. Therefore, the key point of the ICRS design is the power resource allocation between two branches via the selection of a suitable power distribution factor (PWDF). Simulation results demonstrate the good performance of the proposed approach in ranging error and bit error rate (BER). In addition, a reasonable PWDF is recommended. Furthermore, the influence of clock offset is also taken into consideration.
For global navigation satellite system receivers, Kalman filter (KF)-based tracking loops show remarkable advantages in terms of tracking sensitivity and robustness compared with conventional tracking loops. However, to improve the tracking sensitivity further, increasing the coherent integration time is necessary, but it is typically limited by the navigation data bit sign transition. Moreover, for standard KF-based tracking receivers, the KF parameters are initialized by the acquired results. However, especially under weak signal conditions, the acquired results have frequency errors that are too large for KF-based tracking to converge rapidly to a steady state. To solve these problems, a two-stage KF-based tracking architecture is proposed to track weaker signals and achieve faster convergence. In the first stage, coarse tracking refines the acquired results and achieves bit synchronization. Then, in the second stage, fine tracking initializes the KF-based tracking by using the coarse tracking results and extends the coherent integration time without the bit sign transition limitation. This architecture not only utilizes the self-tuning technique of the KF to improve the tracking sensitivity, but also adopts the two-stage to reduce the convergence time of the KF-based tracking. Simulation results demonstrate that the proposed method outperforms conventional tracking techniques in terms of tracking sensitivity. Furthermore, the proposed method is compared with the standard KF-based tracking approach, proving that the proposed method converges more rapidly.
To achieve high-precision positioning using the global navigation satellite system (GNSS), the onboard GNSS receiver integrates real-time kinematic (RTK) technology to enable centimeter-level positioning accuracy. Furthermore, array anti-interference technology is incorporated into the RTK receiver to enhance positioning reliability and mitigate interference in complex environments such as urban areas or regions with high electromagnetic activity. However, this approach can introduce signal distortion, which adversely affects the convergence of RTK positioning. To address the issue of bias introduced by interference suppression in RTK positioning, this paper focuses on error modeling and bias compensation through a phase bias compensation algorithm. A novel phase compensation algorithm is proposed, leveraging the anti-interference weighting coefficients of array elements and the anti-interference output signal. Compared to the conventional minimum variance distortionless response (MVDR) algorithm, the proposed method features a simpler architecture and achieves phase compensation at a lower computational cost using the power inverse (PI) algorithm. Simulation experiments demonstrate the effectiveness of the compensation method, achieving a mean phase bias of approximately 0.25 degrees and a variance of 4.62 degrees. This level of accuracy makes it highly suitable for UAVs operating in challenging environments where precision and reliability are paramount.
In the estimation of the direction of arrival (DOA) for interference signals, the direction-finding error of the multiple signal classification (MUSIC) algorithm will increase in the case of multiple interferences or when the interfering signal power is weak. In this paper, a space-time conversion MUSIC (STC-MUSIC) algorithm is proposed, and the concept of a focusing parameter is introduced to improve the performance of the DOA estimation. Meanwhile, a method of variable step size peak search is proposed to reduce the amount of calculation of the STC-MUSIC algorithm. The final simulation and experimental results show that the STC-MUSIC algorithm improves the purity of the noise subspace effectively, thus improving the precision and robustness of the DOA estimation for interference signals significantly. In comparison to traditional algorithms, the convergence, stability, root mean square error (RMSE) and other performance characteristics are improved greatly.
With the development of navigation satellite constellation systems, to improve navigation service and orbit determination performance, the accuracy requirements for maintaining temporal references have increased rapidly. Among the current navigation satellites, a dual one-way ranging (DOWR) approach based on intersatellite links (ISLs) is widely adopted in the BeiDou system and global positioning system (GPS) to transmit satellite time reference information. However, the accuracy of DOWR is restricted by the pseudonoise (PN) code rate. To improve the accuracy of DOWR, the PN code measurement must be replaced by the carrier phase measurement. This paper introduces an algorithm that utilizes frequency hopping to achieve carrier phase ranging. In addition to the high-precision advantages of carrier phase measurements, the anti-interference performance of the ranging signal is also improved due to the characteristics of the frequency hopping signal itself. Ultimately, at a carrier-to-noise ratio of 40 dB-Hz, the measurement accuracy is 9.54 μm, while the PN code measurement accuracy in the same environment is 0.13 m. As the carrier-to-noise ratio increases, the measurement accuracy further improves.