Daniel Steven Stutts

Prof. Daniel Steven Stutts

Department of Mechanical Engineering, Missouri University of Science and Technology, Rolla, MO 65409-0050, USA
orcid

Research Focus & Metrics

Academic Career Length

36Years (1991-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 January 2005 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
PBP. Beccue
P. Beccue
JNJ. Neely
J. Neely
SPS. Pekarek
S. Pekarek
DSDaniel Steven Stutts
Daniel Steven Stutts
A sensor to measure the stator torsional vibration due to torque ripple produced by a surface mount permanent magnet machine is first described. The sensor is relatively inexpensive and is straight forward to incorporate into a drive system. Experiments are performed to validate that the voltage produced by the sensor is linearly related to torque ripple amplitude. Closed-loop controllers are then described that adjust the stator current harmonics applied to the machine to achieve a commanded average torque while mitigating measured torsional vibration. Simulation and experimental results are used to demonstrate the effectiveness of the control techniques.

28 November 2019 in IEEE Transactions on Antennas and Propagation
Verified
Journal Article
Closed access
HRHossein Rezaei
Hossein Rezaei
VKVictor Khilkevich
Victor Khilkevich
SYShaohui Yong
Shaohui Yong
DSDaniel Steven Stutts
Daniel Steven Stutts
DPDavid Pommerenke
David Pommerenke
Electromagnetic (EM) fields at radio frequencies (RF) cannot penetrate deep into media with high conductivity such as sea water, wet soil, etc. However, moving to the ultra low frequency (ULF) range (300 Hz -3 kHz) allows a considerable range of communication due to the decreased medium loss at low frequencies and a possibility to use the penetrating near field. Magnetically coupled coils are commonly used for near-field magneto-inductive (MI) communication. Alternatively, it is possible to create ULF magnetic fields of sufficient amplitude by rotating permanent magnets. In this work, an ULF magnetic field generator has been created using a rotating permanent magnet. It has been shown that the proposed field generator outperforms a conventional coil source (23 dB of field strength for the same volume and dissipated power that is 0.35 W), which can be a considerable advantage for low size, weight, and power applications. A method to produce amplitude shift keying (ASK) modulation signals using a modulation coil was proposed and analyzed. It was demonstrated that the inductance of the modulation coil is not critical for achieving acceptable modulation ratios, which opens a possibility for a compact ASK generator design. A simple circuit model and analytical formula for modulation efficiency of the generator was proposed and validated by measurement.

24 May 2017 in IEEE Transactions on Electromagnetic Compatibility
Verified
Journal Article
Open access
SYSen Yang
Sen Yang
WWWei Wu
Wei Wu
SXShuai Xu
Shuai Xu
YZYao-Jiang Zhang
Yao-Jiang Zhang
DSDaniel Steven Stutts
Daniel Steven Stutts
DPDavid J. Pommerenke
David J. Pommerenke
A measurement system which uses acoustic vibration to locate passive-intermodulation (PIM) sources in base station antennas is presented. This measurement system uses mechanical vibration to modulate the PIM signal. The modulation of the PIM signal is detected, and its strength or presence/absence is used as guidance for selecting the location of the vibrating transducer. For the method to be successful, the PIM signal must be caused by loose mechanical contacts or loose nonlinear materials. By introducing the acoustic vibration at different locations in the base station antenna and observing if the PIM signal is modulated by the acoustic frequency, the most likely location of the PIM source is identified.

1 July 1997 in Journal of Sound and Vibration
Verified
Journal Article
Closed access
JFJames Friend
James Friend
DSDaniel Steven Stutts
Daniel Steven Stutts

28 February 2003 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
Verified
Journal Article
Closed access
JFJames Friend
James Friend
JSJ. Satonobu
J. Satonobu
KNK. Nakamura
K. Nakamura
SUS. Ueha
S. Ueha
DSDaniel Steven Stutts
Daniel Steven Stutts
This paper describes the design of a piezoelectric tuning-fork, dual-mode motor. The motor uses a single multilayer piezoelectric element in combination with tuning fork and shearing motion to form an actuator using a single drive signal. Finite-element analysis was used in the design of the motor, and the process is described along with the selection of the device's materials and its performance. Swaging was used to mount the multilayer piezoelectric element within the stator. Prototypes of the 25-mm long bidirectional actuator achieved a maximum linear no-load speed of 16.5 cm/s, a maximum linear force of 1.86 N, and maximum efficiency of 18.9%.

1 September 2016 in Journal of Natural Gas Science and Engineering
Verified
Journal Article
Closed access
MDMohammed F. Al Dushaishi
Mohammed F. Al Dushaishi
RNRunar Nygaard
Runar Nygaard
DSDaniel Steven Stutts
Daniel Steven Stutts