Eugeniusz Ziółkowski

Dr. Eugeniusz Ziółkowski

orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2012 in Archives of Foundry Engineering
Verified
Journal Article
Open access
PDF file
EZEugeniusz Ziółkowski
Eugeniusz Ziółkowski
PŚP. Śmierciak
P. Śmierciak
Foundry resistance furnaces are thermal devices with a relatively large time delay in their response to a change in power parameters. Commonly used in automation classical PID controllers do not meet the requirements of high-quality control. Developed in recent years, fuzzy control theory is increasingly being used in various branches of economy and industry. Fuzzy controllers allow to introduce new developments in control systems of foundry furnaces as well. Correctly selected fuzzy controller can significantly reduce energy consumption in a controlled thermal process of heating equipment. The article presents a comparison of energy consumption by control system of foundry resistance furnace, equipped with either a PID controller or fuzzy controller optimally chosen.

1 December 2017 in Archives of Metallurgy and Materials
Verified
Journal Article
Open access
PDF file
EZEugeniusz Ziółkowski
Eugeniusz Ziółkowski
Calculation of economically optimum charge burden for foundry furnaces depends on a solution that can be found in the field of mathematical linear programming. A traditional linear optimisation method means looking for continuous variables that can define portion of every charge component.Sometimes, it can be observed that a calculated portion of charge material with a defined lump mass is rounded up, which is wrong because the charge burden prepared in such a way may either show a mistaken chemical composition, or it can entail a significant cost. With charge materials characterised by defined mass lumps, it is recommended to use a modified method of integer linear optimisation.This article contains definitions of a goal function and a system of constraints considering the charge materials as stated above. In addition, a sample calculation has been included hereto to show such optimisation for a selected process of metal melting in a casting furnace.

1 April 2012 in Archives of Foundry Engineering
Verified
Journal Article
Open access
PDF file
EZEugeniusz Ziółkowski
Eugeniusz Ziółkowski
Marcin BrzezińskiMarcin Brzeziński
Marcin Brzeziński
RWR. Wrona
R. Wrona
KSK. Smyksy
K. Smyksy
PZP. Zyzak
P. Zyzak
Applications of Monitoring of Electric Power Parameters to Performance Evaluation of a Model Vacuum-Assisted Moulding Installation: Vacuum conditions in foundry installations are generated using electric-driven vacuum pumps. The purpose of the experiment is to evaluate the performance of a vacuum-assisted system for compaction of moulding sand basing on registered plots of selected electric power parameters of the power-supplying system of the pumps. Model testing done on an experimental vacuum system installation, power-supplied from a system incorporating the recorders of instantaneous current and voltage values. Following the numerical procedure, the experimental data are analysed to yield mathematical relationships between the variations of the generated vacuum pressure levels and variations of selected electric power parameters. Registered and computed values of selected parameters: instantaneous and RMS voltage and current values, active, reactive and apparent power levels and power coefficient allow for diagnosing the adequacy and reliability of the system operation. According to the authors, the applied monitoring of the power parameters of a vacuum-assisted installation may become an effective and easy practical method of evaluating the performance of such installations, used also in foundry plants.

14 May 2024 in Materials
Verified
Journal Article
Open access
PDF file
ABAndriy Burbelko
Andriy Burbelko
TWTomasz Wiktor
Tomasz Wiktor
Aldona Garbacz-KlempkaAldona Garbacz-Klempka
Aldona Garbacz-Klempka
EZEugeniusz Ziółkowski
Eugeniusz Ziółkowski
To perform quality assessments of both metal alloys and many other engineering materials, measurements of the volume fractions of phases or microstructure components are utilized. For this purpose, quantitative analysis of the evaluated components’ distribution on metallographic specimens is often employed. Phases or components of the microstructure are identified based on the variation in signal received in the band of light seen. Problems with the correct identification of measurement results in this spectral band can be caused by the inhomogeneity of the etching when the alloy components are segregated. Additional uncertainty arises when the analyzed image pixel contains a boundary between grains of different phases. This article attempts to use the results of local chemical composition measurements as a source signal for quantitative evaluation of phase composition. For this purpose, quantitative maps of elemental concentration distributions, obtained with a Tescan Mira GMU high-resolution scanning electron microscope in QuantMap mode, were used as input data for the phase composition evaluation of an EN AC 46000 alloy sample. The X-ray microanalysis signal generation area may contain grains of more than one phase. Therefore, evaluation of the phase fractions in areas of individual measurements were calculated by looking for the minimum of the objective function, calculated as the sum of the squares of the deviations of the results of measurements of the concentration of individual elements from the weighted average values of solubilities of these elements in the phases.

17 July 2023 in Archives of Foundry Engineering
Verified
Journal Article
Open access
JMJan Mędoń
Jan Mędoń
ASAndrzej Szczęsny
Andrzej Szczęsny
EZEugeniusz Ziółkowski
Eugeniusz Ziółkowski
EGEdward Guzik
Edward Guzik
MCM. Czarny
M. Czarny
DKDariusz Kopyciński
Dariusz Kopyciński

1 September 2013 in Archives of Foundry Engineering
Verified
Journal Article
Open access
PDF file
KSK. Smyksy
K. Smyksy
RWR. Wrona
R. Wrona
EZEugeniusz Ziółkowski
Eugeniusz Ziółkowski
Investigations of operating parameters of widely used sand mixers reveal a wide variability range in the values of parameters associated with their power demand. Power efficiency of manufacturing processes has received a great deal of attention lately, which encourages the research efforts to optimise this aspects of operation of machines and installations as well. In the first place these machines and installations have to work properly as a part of the process line- which applies also to moulding sand mixers. Experiments conducted by the authors suggest that the same goal can be achieved at variable energy input levels. To obtain information about the power demands of sand mixers requires the use of highly specialised equipment, methodology and result processing procedures. This study provides a brief characteristic of measurement equipment and results of measurements taken on a unit AG-015 (based on a roller mixer) and a laboratory rotor mixer.