The increase in greenhouse gas emissions, as well as the risk of fossil fuel depletion, has prompted a transition to electric transportation. The European Union aims to substantially reduce pollutant emissions by 2035 through the use of renewable energies. In aviation, this transition is particularly challenging, mainly due to the weight of onboard equipment. Traditional electric motors with radial magnetic flux have been replaced by axial magnetic flux motors with reduced weight and volume, high efficiency, power, and torque. These motors were initially developed for electric vehicles with in-wheel motors but have been adapted for aviation without modifications. Worldwide, there are already companies developing propulsion systems for various aircraft categories using such electric motors. One category of aircraft that could benefit from this electric motor development is traditionally constructed training aircraft with significant remaining flight resource. Electric repowering would allow their continued use for pilot training, preparing them for future electrically powered aircraft. This article presents a study on the feasibility of repowering a classic training aircraft with an electric propulsion system. The possibilities of using either a battery or a hybrid source composed of a battery and a fuel cell as an energy source are explored. The goal is to utilize components already in production to eliminate the research phase for specific aircraft components.
(1) Introduction: The changes in the joint morphology inevitably lead to prosthesis, but the hip pathology is complex. The hip arthroplasty is a therapeutic solution and can be caused, most frequently, by primary and secondary coxarthrosis due to or followed by traumatic conditions. The main aim of this study was to find the method of revision hip prosthesis that preserves as much bone material as possible and has sufficiently good mechanical strength. (2) Materials and Methods: In this study, in a first step, the two revision prostheses were performed on bone components taken from an animal (cow), and then, they were tested on a mechanical testing machine until the prostheses physically failed, and the force causing their failure was determined. (3) Results: These prostheses were then modelled in a virtual environment and tested using the finite element method (FEM) in order to determine their behaviour under loading from normal human gait. Displacement, strain, and stress maps were obtained. (4) Discussion: Discussions on hip revision prostheses, method, and theory analysis are presented at the end of the paper. (5) Conclusions: Important conclusions are drawn based on comparative analyses. The main conclusion shows that the both orthopaedic prostheses provide a very good resistance.
1 February 2020 in Applied Mechanics and Materials
For a building equipped with anti-seismic devices, the value of the damping force of the dampers positioned at the superstructure is very important for an efficient anti-seismic damping and therefore an optimization of the seismic protection system with dampers is required. There are several configurations for placing the dampers that amplify the displacement and the damper axial force. This paper presents a computational mathematical model made for determining the coefficients of displacement multiplication and the damping force multiplication for two special positioning configurations of the antiseismic dampers using levers. Based on this model, a software program was created that allows to choose the geometrical parameters of two configurations of dampers placement having as criterion of choice the value of the amplification coefficient of the dampers displacement or the damper axial force.
This paper presents the simulation of the influence of viscoelastic fluid dampers, with nonlinear damping properties, on damping property of a ten stories building structure. The study was made using Finite Elements Method and ANSYS program, on a 3d F.E.M. model. In order to obtain the influence of different types of damping nonlinearities of the viscoelastic fluid dampers on the damping property of the entire structure, there were made different types of simulations using modal analysis and seismic time history analysis. The graphics obtained can be used for determining the nonlinear features of fluid dampers for achieving different degrees of seismic energy dissipation for the analyzed building.
This paper presents a comparison of some different configurations of electro-hydrostatic actuators (EHA). The gear pump EHA has a simpler mechanical configuration, but the electronic power command circuits and the electric motor are in high demand due to the very frequent speed variations. The variable piston pump EHA has a more complicated mechanical configuration, but the electronic power command circuits and the main electric motor are less loaded due to the constant speed of the electric motor. The variable displacement pump control can be made either using an electric motor and mechanical transmission, or an additional hydraulic circuit, to modify the swash plate angle. In total, four EHA configurations are studied in this paper (one with a gear pump and three with variable axial piston pumps). The paper aims to advantages and disadvantages of each type of EHA, using numerical simulations.
The paper is based on dynamic modeling research and experimental results obtained for freshly compacted concrete under stationary vibration. Thus, computational relationships and laws for vibration parameters and dissipated energy will be presented. In correlation with the dissipated energy, it will be evidenced by the evolution of the compaction degree and the resistance of the concrete depending on the vibration duration. It is noted that significant correlations have been established between the displacement curve of the dissipated energy and the loop hysteresis area for several vibration frequencies specific to the dynamic compaction regime