Sreeja Sadasivan

Dr. Sreeja Sadasivan

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 January 2018 in Archives of Computational Methods in Engineering
Verified
Journal Article
Closed access
PDF file
BJBibin John
Bibin John
PSP. Senthilkumar
P. Senthilkumar
SSSreeja Sadasivan
Sreeja Sadasivan

18 February 2025 in Microfluidics and Nanofluidics
Verified
Journal Article
Closed access
PDF file
SSSreeja Sadasivan
Sreeja Sadasivan
SPS. Pradeep
S. Pradeep
JRJishnu Chandran Ramachandran
Jishnu Chandran Ramachandran
JNJayaprakash Narayan
Jayaprakash Narayan
MGMichał Jan Gęca
Michał Jan Gęca

1 January 2019 in Journal of Applied Fluid Mechanics
Verified
Journal Article
Closed access
SGS. A. Gillani
S. A. Gillani
VPV. P. Panikulam
V. P. Panikulam
SSSreeja Sadasivan
Sreeja Sadasivan
ZYZ. Yaoping
Z. Yaoping

1 December 2024 in Physics of Fluids
Verified
Journal Article
Closed access
JRJishnu Chandran R
Jishnu Chandran R
SSSreeja Sadasivan
Sreeja Sadasivan
Senthil Kumar AnantharajanSenthil Kumar Anantharajan
Senthil Kumar Anantharajan
FCFei Chen
Fei Chen
Transcritical refrigeration systems using natural refrigerants like CO2 operate on the ejector–expansion cycle to achieve high operating efficiency. The variability of ejector geometry dictates the adjustability of refrigerating capacity in such systems. Traditional spindle-controlled axial-flow ejectors significantly obstruct the high-pressure motive flow to regulate mass flow rate by controlling flow area. This study introduces the first radial-flow ejector geometry for transcritical CO2 refrigeration systems, designed to operate at high mass flow rates and entrainment ratios with minimal obstruction to motive flow. The study numerically investigates the performance of a radial-flow two-phase ejector for CO2, comparing it with an axial-flow ejector of similar dimensions under the same conditions. It explores the impact of applied compression ratio, motive nozzle throat spacing, and other geometries on radial ejector performance. An increase in the motive throat spacing improves the range of operable discharge pressures and achievable compression ratios, with a slight reduction in the secondary flow entrainment. A nozzle throat spacing of 0.6 mm allows a wider range of operable discharge pressures, and beyond this, the operable discharge pressure range drops. The addition of a diffuser section of sufficient length also improves the flow entrainment in the radial ejector. The radial ejector allows substantially high mass flow rates of even 15 times that of the axial ejector. This high mass flow capacity in the radial configuration can significantly compact ejector designs for large-capacity transcritical CO2 refrigeration and air-conditioning systems.

1 January 2019 in Journal of Applied Fluid Mechanics
Verified
Journal Article
Closed access
SSSreeja Sadasivan
Sreeja Sadasivan
SAS. K. Arumugam
S. K. Arumugam
MAM. Aggarwal
M. Aggarwal

8 April 2024 in Energies
Verified
Journal Article
Open access
PDF file
SSSreeja Sadasivan
Sreeja Sadasivan
Grzegorz LitakGrzegorz Litak
Grzegorz Litak
MGMichal Jan Geca
Michal Jan Geca
Numerical calculations were performed to study the vortex-induced vibration (VIV) of a circular cylinder, which was elastically supported by springs of linear and cubic terms. These simulations were conducted at high Reynolds numbers ranging from 4200 to 42,000. To simulate the cylinder’s motion and the associated aerodynamic forces, Computational Fluid Dynamics were employed in conjunction with dynamic mesh capabilities. The numerical method was initially verified by testing it with various grid resolutions and time steps, and subsequently, it was validated using experimental data. The response of cubic nonlinearities was investigated using insights gained from a conventional linear vortex-induced vibration (VIV) system. This 2D study revealed that both the amplitude and frequency of vibrations are contingent on the flow velocity. The highest output was achieved within the frequency lock-in region, where internal resonance occurs. In the case of a hardening spring, the beating response was observed from the lower end of the initial branch to the upper end of the initial branch. The response displacement amplitude obtained for the linear spring case was 27 mm, whereas in the cubic nonlinear case, the value was 31.8 mm. More importantly, the results indicate that the inclusion of nonlinear springs can substantially extend the range of wind velocities in which significant energy extraction through vortex-induced vibration (VIV) is achievable.