It is believed that materials based on ultrafine (nanoscale) diamond powders can possess high-level physical-mechanical and performance parameters characteristic of a nanocrystalline state. In certain cases, however, conventional methods for compacting ultrafine-dispersed diamonds (UDDs) fail and cannot be used to fabricate materials with desired properties. The difficulties associated with the ultrafine-dispersed state of the initial diamond powders can be surmounted by modifying the chemical and phase composition of the UDD surface. The possible use of UDDs as a catalyst that is conductive to the occurrence of chemical and phase transformations in certain substances at high pressures is analyzed. Sintering UDDs in the region of metastability of diamond makes it possible to produce porous polycrystalline aggregates with large specific surface area and very hard transparent particles.
Titanium alloys are widely used in aerospace applications due to their high specific strength and exceptional corrosion resistance. In this study, a silicide coating with a multi-layer structure was designed and prepared via a pack cementation process to improve the high-temperature oxidation resistance of titanium alloy. A new theory based on the Le Chatelier’s principle is proposed to explain the generation mechanism of active Si atoms. Taking the chemical potential as a bridge, a functional model of the relationship between the diffusion driving force and the change in the Gibbs free energy of reaction diffusion is established. Experimental results indicate that the depth of the silicide coating increases with the siliconization temperature (1000–1100 °C) and time (0–5 h). The multi-layer coating prepared at 1075 °C for 3 h exhibits a thick and dense structure with a thickness of 23.52 μm. This coating consists of an outer layer of TiSi2 (9.40 μm), a middle layer of TiSi (3.36 μm), and an inner layer of Ti5Si3 (10.76 μm). Under this preparation parameter, increasing the temperature or prolonging the holding time will cause the outward diffusion flux of atoms in the substrate to be much larger than the diffusion flux of silicon atoms to the substrate, thus forming pores in the coating. The calculated value of the diffusion driving force FTiSi = 2.012S is significantly smaller than that of = 13.120S and = 14.552S, which perfectly reveals the relationship between the thickness of each layer in the Ti–Si multi-layer coating.
VRV.S. Sobolev Institute of Geology and Mineralogy of the Siberian Branch of the RAS
V.S. Sobolev Institute of Geology and Mineralogy of the Siberian Branch of the RAS
+4
The article studies the structure, phase composition and physicomechanical characteristics of the nanocomposite based on impact diamonds. It is shown that the additions of a binder based on SiC and Si lead to reduction of the defectiveness of the nanocomposite and increase in the uniformity of its structure compared to the material without additives. Moreover, increase in the binder content also leads to the inversion of the structure type of the nanocomposite from polycrystalline to matrix. It is established that the addition of amorphous carbon black and boron affects the refinement of the nanocomposite matrix structure due to the formation of secondary finedispersed nanostructured SiC and boron carbide. Preliminary mechanical activation of the reaction mixture leads to structural changes in the synthesized material in comparison with the material obtained without the use of mechanical activation. In this case, the hardness of the samples obtained under comparable synthesis modes increases, which is associated both with the formation of a fine-grained structure of the material and with the phase transformation of lonsdaleite to diamond. An analysis of the microhardness and heat resistance of the obtained samples makes it possible to conclude that the achieved level of physicomechanical parameters of the diamond nanocomposite allows it to be used in a stone-processing tool for treating medium hard rocks.
1 January 2022 in Image Journal of Advanced Materials and Technologies
During sintering of a nanodiamond powder with a coating based on non-diamond forms of carbon with a thickness of about 10 Å at relatively low pressures and temperatures, a nanostructured diamond material is formed by the transition of graphite-like carbon to diamond. It has been shown that nanodiamond powder modified with non-diamond forms of carbon is an “active” base on which a nanometer layer of graphite-like carbon transforms into diamond during thermobaric sintering. The influence of preliminary annealing of nanodiamonds in a disammonia atmosphere and in oxidizing and hydrocarbon-containing atmospheres on the structure and microhardness of nanodiamond polycrystals has been shown. It has been established that the atmosphere in which modifying annealing is carried out affects the content of the diamond phase and the size of nanodiamond crystallites in a polycrystalline material. The preliminary modification (functionalization) of the nanodiamond surface with carbon-containing compounds stimulates the process of diamond formation. In this case, the most significant increase in the microhardness of diamond polycrystals is observed after the modification of nanodiamonds in oxidizing and hydrocarbon atmospheres. It has also been established that the modifying treatment of nanodiamonds with hydrocarbons stimulates the processes of diamond synthesis, and an increase in pressure suppresses the graphitization of diamond and activates the transformation of graphite-like carbon into diamond, which contributes to sintering of diamond grains.
1 November 2018 in Proceedings of the National Academy of Sciences of Belarus. Physical-technical series
Проведено исследование структуры и микротвердости алюминиевого сплава с добавками наноструктурного кубического нитрида бора (cBN) после обработки в условиях высоких давлений и температур. В качестве наполнителя применяли наноструктурный порошок сBN с размером первичных частиц в пределах 50–200 нм. Для повышения химического сродства наноструктурного cBN к алюминиевой матрице проведено предварительное химико-термическое модифицирование наноструктурного cBN, заключавшееся в его высокотемпературной обработке (отжиге) в диапазоне температур 750–950 °С в среде алюмосодержащих соединений. Показано, что модифицирование наноструктурного нитрида бора алюминием способствует прочности удержания наполнителя в алюминиевой матрице. При этом увеличение в шихте концентрации наполнителя BN от 1,5 до 5 мас.%, а также повышение температуры обработки при фиксированном давлении способствует возрастанию микротвердости материала в 1,5– 2 раза по сравнению с базовым алюминиевым сплавом без добавок модификатора. Повышение концентрации BN до 5 мас.% приводит к увеличению в материале доли более мелких конгломератов частиц (1–5 мкм), уменьшению размеров крупных включений до 10–20 мкм, при этом распределение включений из частиц BN в алюминиевой матрице более равномерное по сравнению с материалом, содержащим 1,5 мас.% cBN. С ростом температуры до 1000 оС в материале происходит рекристаллизация cBN в агрегатах с образованием его отдельных монокристаллических (поликристаллических) частиц размерами 1–10 мкм, обладающих огранкой, характерной для микрочастиц cBN.