ELENA PICAZO CAMILO

Dr. ELENA PICAZO CAMILO

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 April 2024 in Sustainability
Verified
Journal Article
Open access
PDF file
RCRaúl Carrillo-Beltrán
Raúl Carrillo-Beltrán
ECELENA PICAZO CAMILO
ELENA PICAZO CAMILO
GTGriselda Elisabeth Perea Toledo
Griselda Elisabeth Perea Toledo
FIFrancisco Antonio Corpas Iglesias
Francisco Antonio Corpas Iglesias
In recent years, the mining industry of slate stone in Spain, from Castille and Leon, has grown significantly due to construction and building sector demands. The continuous accumulation of cutting sludges in ponds from mining and processing operations brings associated environmental problems if the cutting sludges are not properly treated. A potential environmental mitigation measure is the valorization of cutting sludges for the development of new binder materials through geopolymerization. Therefore, this research focused its attention on studying the feasibility of slate stone cutting sludges as a source of aluminosilicates for geopolymer conformation. For this experiment, the mining raw material was analyzed through a typical characterization test campaign in order to validate its feasibility as a source of aluminosilicates for geopolymerization. Subsequently, geopolymers were prepared with slate stone cutting sludges and a 12 M concentration using different Na2SiO3/NaOH ratios (5, 2.5, 1.6, 1.25, and 1). Geopolymer samples were tested, and their physical and mechanical characteristics were evaluated. The test results show that an alkali activator with a 2.5 ratio led to better mechanical and physical properties, with a 7-day compressive strength value of 27.23 MPa. Therefore, this research aims to demonstrate that slate stone cutting sludge could constitute a sustainable binder material for construction purposes.

23 December 2024 in Polymers
Verified
Journal Article
Open access
PDF file
JEJuan José Valenzuela Expósito
Juan José Valenzuela Expósito
ECELENA PICAZO CAMILO
ELENA PICAZO CAMILO
FIFrancisco Antonio Corpas Iglesias
Francisco Antonio Corpas Iglesias
In recent years, the construction industry has faced challenges related to rising material costs, labor shortages and environmental sustainability, resulting in an increased interest in modular construction cores composed of recycled materials, such as XPS, PUR, PLW and GFRP, from waste from the truck body industry. Two resins, PUR and polyester, were used to bond these recycled composites. Physical, chemical and mechanical analyses showed that the panels formed with PUR resin had superior workability due to the higher open time of the resin, 11.3% better thermal conductivity than the commercial PLW panel (SP-PLW) and reduced porosity compared to those using polyester resin. The mechanical performance of the panels improved with higher structural reinforcement content (PLW and GFRP). Compared to a commercial panel (SP-PLW), the SP-RCM1 recycled panel showed 4% higher performance, demonstrating its potential for sustainable building applications. Thermal and microscopic characterizations showed good adhesion of the materials in the best performing formulations related to higher thermal stability. Therefore, this research aims to demonstrate the feasibility of using waste from the car industry in the manufacture of sandwich panels for modular construction to address these issues.

4 February 2025 in Materials
Verified
Journal Article
Open access
PDF file
RCRaúl Carrillo-Beltrán
Raúl Carrillo-Beltrán
ECELENA PICAZO CAMILO
ELENA PICAZO CAMILO
GTGriselda Elisabeth Perea Toledo
Griselda Elisabeth Perea Toledo
FIFrancisco Antonio Corpas Iglesias
Francisco Antonio Corpas Iglesias
The reuse of by-products as alternative raw materials to traditional construction materials is required in order to ensure sustainable development in the construction sector and is a significant and important focus in the fields of materials science. This study developed geopolymers using by-products from mining, ceramics, and olive industries, including slate stone cutting sludge (SSCS) and chamotte (CH) as aluminosilicate sources, and olive biomass bottom ash (OSBA) as an alkaline activator with sodium silicate. A key novelty of the research lies in the use of SSCS, an underexplored by-product in geopolymerization studies, as a viable aluminosilicate source. The geopolymers were prepared with varying weight ratios of SSCS, CH, and OSBA/Na₂SiO₃ (1.7, 1.9, 2.2, and 2.4). Physical and mechanical tests determined the optimal formulation, while FTIR and SEM analyses revealed the material’s chemical and structural evolution. The FTIR analysis detected the quartz and carbonate phases, indicating incomplete quartz dissolution and carbonate formation during calcination. The SEM analysis revealed a dense microstructure with reduced porosity and enhanced geopolymerization in samples with higher OSBA content. The optimal geopolymer (60% OSBA, 30% CH, OSBA/Na₂SiO₃ ratio of 2.2) achieved a compressive strength of 33.1 MPa after 28 days. These findings demonstrate the feasibility of producing geopolymers using SSCS, CH, and OSBA, promoting the reuse of industrial by-products as sustainable alternatives to conventional binders.

Verified
Journal Article
Open access
PDF file
JEJuan José Valenzuela Expósito
Juan José Valenzuela Expósito
ECELENA PICAZO CAMILO
ELENA PICAZO CAMILO
FIFrancisco Antonio Corpas Iglesias
Francisco Antonio Corpas Iglesias
This study explores the development and optimization of TiO2-based photoactive coatings enhanced with silver (Ag)—to boost photocatalytic performance—for application on glass-fiber-reinforced polyester (GFRP) and epoxy (GFRE) composites. The influence of Ag content on the structural, physicochemical, and functional properties of the coatings was evaluated. The TiO2-Ag coating showed the best performance and was tested under UV-A irradiation and visible light (Vis), with high efficiency in VOC degradation, self-cleaning, and microbial activity. The tests were repeated in multiple runs, showing high reproducibility in the results obtained. In GFRP, pollutant and microorganism removal ratios of more than 90% were observed. In contrast, GFRE showed a lower adhesion and stability of the coating. This result is attributed to incompatibility problems with the epoxy matrix, which significantly limited its functional performance. The results highlight the feasibility of using the TiO2-Ag coating on GFRP substrates, even under visible light. Under real-world conditions for 351 days, the coating on GFRP maintained its stability. This type of material has high potential for application in modular building systems using sandwich panels, as well as in facades and automotive components, where self-cleaning and contaminant-control properties are essential.

13 April 2025 in Materials
Verified
Journal Article
Open access
PDF file
ECELENA PICAZO CAMILO
ELENA PICAZO CAMILO
JEJuan José Valenzuela Expósito
Juan José Valenzuela Expósito
RCRaúl Carrillo-Beltrán
Raúl Carrillo-Beltrán
GTGriselda Elisabeth Perea Toledo
Griselda Elisabeth Perea Toledo
FIFrancisco Antonio Corpas Iglesias
Francisco Antonio Corpas Iglesias
The sustainable development of building materials is based on reusing by-products to reduce environmental impact and promote alternatives to traditional materials. In this study, geopolymers were developed from by-products of the mining, ceramic, and thermal industries: slate stone cutting sludge (SSCS) and chamotte (CH) as aluminosilicate sources, and olive stone bottom ash (OSBA) as an alkaline activator, combined with sodium silicate (Na2SiO3). Eight geopolymer families were prepared with constant amounts of SSCS and CH and varying proportions of OSBA/Na2SiO3 (0.88–1.31). The evaluation phase included physical, chemical, mechanical, and microstructural tests. The results showed that the optimum geopolymer formulation (GP E) contained 25% SSCS, 15% CH, and 19% OSBA with a Na2SiO3/OSBA ratio of 1.0, achieving a compressive strength of 24.12 MPa after 28 days of curing. GP E also showed the lowest porosity (19.54%), minimal water absorption (6.86%), and favorable thermal conductivity (0.688 W/mK). Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM) confirmed the formation of dense and homogeneous matrices. These results demonstrate the feasibility of manufacturing geopolymers using SSCS, CH, and OSBA as substitutes for traditional binders, promoting sustainable practices, reusing industrial by-products, and reducing carbon emissions in construction.

26 April 2025 in Materials
Verified
Journal Article
Open access
PDF file
RCRaúl Carrillo-Beltrán
Raúl Carrillo-Beltrán
ECELENA PICAZO CAMILO
ELENA PICAZO CAMILO
GTGriselda Elisabeth Perea Toledo
Griselda Elisabeth Perea Toledo
FIFrancisco Antonio Corpas Iglesias
Francisco Antonio Corpas Iglesias
The expansion of the construction sector has contributed to the depletion of raw materials and an increased demand for resources; therefore, sustainable approaches are required to satisfy the construction demand. The present study explores the development of geopolymers by utilizing industrial by-products from mining, ceramics, olive oil production, and steel manufacturing. Specifically, slate stone cutting sludge (SSCS) and chamotte (CH) are used as aluminosilicate precursors, with olive biomass bottom ash (OSBA) acting as an alkaline activator, along with sodium silicate, and steel granulated slag (SGS) incorporated as an aggregate. Novel geopolymers were prepared with consistent proportions of SSCS and OSBA while varying the CH content from 10 to 2 wt.%. The SGS proportion was adjusted from 35 to 50 wt.%, and different Na2SiO3/OSBA ratios (0.35, 0.31, 0.19, and 0.08) were examined. To identify the optimal mix, a series of physical and mechanical tests was conducted, complemented by FTIR and SEM analysis to evaluate the chemical and microstructural changes. The best-performing formulation achieved a compressive strength of 42.8 MPa after 28 days of curing. FTIR analysis identified quartz and carbonate phases, suggesting that quartz did not fully dissolve and that carbonates formed during the heating process. SEM examination of the optimal mixture indicated that the incorporation of SGS (up to 45 wt.%) facilitated the creation of a compact, low-porosity structure. EDX results revealed the presence of Ca-, Na-, Si-, Al-, and K-enriched phases, supporting the formation of (N, C)-A-S-H gel networks. These results demonstrate the potential of utilizing SSCS, CH, OSBA, and SGS to create geopolymer concretes, showcasing the viability of using industrial by-products as eco-friendly substitutes for traditional construction materials.