Xueyan S. Xu

Dr. Xueyan S. Xu


Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2017 in International Journal of Industrial Ergonomics
Verified
Journal Article
Closed access
XXXueyan S. Xu
Xueyan S. Xu
RDRen G. Dong
Ren G. Dong
DWDaniel E. Welcome
Daniel E. Welcome
CWChristopher Warren
Christopher Warren
TMThomas W. McDowell
Thomas W. McDowell
JWJohn Z. Wu
John Z. Wu

15 June 2021 in Vibration
Verified
Journal Article
Open access
PDF file
RDRenguang Dong
Renguang Dong
JWJohn Z. Wu
John Z. Wu
XXXueyan S. Xu
Xueyan S. Xu
DWDaniel E. Welcome
Daniel E. Welcome
Kristine KrajnakKristine Krajnak
Kristine Krajnak
Studies on hand-transmitted vibration exposure, biodynamic responses, and biological effects were conducted by researchers at the Health Effects Laboratory Division (HELD) of the National Institute for Occupational Safety and Health (NIOSH) during the last 20 years. These studies are systematically reviewed in this report, along with the identification of areas where additional research is needed. The majority of the studies cover the following aspects: (i) the methods and techniques for measuring hand-transmitted vibration exposure; (ii) vibration biodynamics of the hand–arm system and the quantification of vibration exposure; (iii) biological effects of hand-transmitted vibration exposure; (iv) measurements of vibration-induced health effects; (iv) quantification of influencing biomechanical effects; and (v) intervention methods and technologies for controlling hand-transmitted vibration exposure. The major findings of the studies are summarized and discussed.

1 September 2015 in Measurement
Verified
Journal Article
Closed access
XXXueyan S. Xu
Xueyan S. Xu
RDRen G. Dong
Ren G. Dong
DWDaniel E. Welcome
Daniel E. Welcome
CWChristopher Warren
Christopher Warren
TMThomas W. McDowell
Thomas W. McDowell

1 April 2019 in Measurement
Verified
Journal Article
Closed access
XXXueyan S. Xu
Xueyan S. Xu
DWDaniel E. Welcome
Daniel E. Welcome
CWChristopher M. Warren
Christopher M. Warren
TMThomas W. McDowell
Thomas W. McDowell
RDRen G. Dong
Ren G. Dong

1 September 2021 in Applied Ergonomics
Verified
Journal Article
Closed access
XXXueyan S. Xu
Xueyan S. Xu
DWDaniel E. Welcome
Daniel E. Welcome
TMThomas W. McDowell
Thomas W. McDowell
CWChristopher Warren
Christopher Warren
SSSamantha Service
Samantha Service
RDRen G. Dong
Ren G. Dong

28 June 2020 in Journal of Low Frequency Noise, Vibration and Active Control
Verified
Journal Article
Open access
PDF file
XXXueyan S. Xu
Xueyan S. Xu
DWDaniel E Welcome
Daniel E Welcome
TMThomas W McDowell
Thomas W McDowell
CWChristopher Warren
Christopher Warren
HLHansheng Lin
Hansheng Lin
RDRen G Dong
Ren G Dong
The objective of this study is to characterize the vibration responses of a handheld workpiece and the hand–arm system, which is an important step toward identifying and developing effective methods and technologies for controlling the vibration exposures to workers performing the grinding of handheld workpieces. This study established a method for measuring the vibration responses of the entire workpiece–hand–arm system; the vibration exposure of a worker holding and pressing a typical workpiece against a sanding belt or grinding wheel in order to shape the workpiece was simulated. This method was applied to measure the apparent mass and vibration transmissibility of the system under two different feed forces (15 N and 30 N) and six simulated grinding interfaces with different stiffness values. A major resonance was observed in each transmissibility spectrum of the workpiece, which was correlated with the major resonance of the impedance of the entire system. This resonant frequency depended primarily on the workpiece mass and the grinding interface stiffness, but the hand–arm system could substantially affect the resonance magnitude. The feed force also significantly affected the resonance frequency and magnitude. While increasing the feed force increased the overall vibration transmissibility on the hand–arm system, the transmissibility with respect to the workpiece was not significantly affected by the interface conditions. The implications of the results are discussed.