The fire-extinguishing system is an indispensable fire-protection facility on the aircraft. In order to guide weight reduction of the aircraft’s fixed gas fire-extinguishing system by improving its release efficiency, so as to improve fuel economy and reduce carbon emissions, the influence of filling pressures and filling amounts on the release efficiency of gas extinguishing agent along pipelines were studied based on numerical simulations. The release process of the fire-extinguishing system was analyzed. The effects of the filling pressure and filling amount of Halon 1301 agent on the release characteristics, such as release time, mass flow rate, and gasification ratio, were studied. Results show that the release process can be divided into three major phases, which are firstly the initial rapid filling of the pipeline, secondly the concentrated release of the liquid extinguishing agent, and thirdly the gas ejection along the pipeline. The second phase can also be subdivided into two stages: the outflow of the liquid extinguishing agent from the bottle, and the release of the residual liquid extinguishing agent along the pipeline. The release characteristics of the fire-extinguishing agent were obviously affected by the filling pressures and filling amounts. When the filling pressure was relatively low (2.832 MPa), increasing the filling pressure can significantly increase the mass flow rate, shorten the release time, and reduce the gasification ratio of the extinguishing agent during the release processes. Under the same filling pressure, with the increase of the filling amount of the extinguishing agent, the release times and the gasification ratio showed a linear increase trend, while the average mass flow rates showed a linear decrease trend.
In order to guide the optimization design of the pipeline network of the aircraft-fixed gas fire extinguishing system and improve its fire extinguishing performance, FLUENT software was used to simulate the influence of pipeline parameters such as diameter, length, and roughness on the release characteristics of the fire extinguishing agent. It can be found that the extinguishing agent can be divided into liquid and vapor extinguishing agents in the fire extinguishing pipeline system during the release. The spatial distribution and proportion of the liquid and vapor extinguishing agents are asymmetric. Results show that the peak value of the pressure drop rate () has a good quadratic function relationship with the pipeline diameter () and the functional relationship is which means that the peak value increased significantly with the increase in the pipeline diameter. Moreover, when the pipeline diameter is 25 , the average pressure drop rate of the vessel is about 35.02 , which is 5.97 times the value of the average pressure drop rate when the pipeline diameter is 10 . With the increase in the pipeline diameter, the release time decreases significantly, the mass flow rate increases obviously, while the gasification ratio decreases rapidly at first and then increases slightly. The pipeline length also has a significant influence on the release characteristics of the extinguishing agent. With the increase in the pipeline length, the release time and the gasification ratio increase linearly, while the mass flow rate decreases linearly. Compared with the pipeline diameter and pipeline length, the influence of the pipeline roughness on the release characteristics of the extinguishing agent is weak. With the increase in the pipeline roughness, the release time and the gasification ratio of the extinguishing agent increases slowly, while the mass flow rate decreases slowly.
The relationship between the structure characteristics and performances of coal-based hydrogenation isomeric (CTL) base oil and metallocene-catalyzed coal-based poly-alpha-olefin (mPAO) base oil is clarified in this paper. CTL and mPAO were compared with typical petroleum-based and natural gas-based commercial API III and IV base oils. Pressurized differential scanning calorimetry (PDSC), the rotary bomb oxidation test (RBOT), and a four-ball friction tester were used to evaluate the oxidation stability and lubrication performance of base oils under different working conditions. The sensitivity of different base oils to typical antioxidants and extreme-pressure antiwear agents was compared. In particular, the composition and structure of CTL base oil are clearly different from GTL and mineral base oil. The coal-based CTL and mPAO base oils exhibit commendable viscosity–temperature properties, coupled with low-temperature fluidity, fire safety, and minimal evaporation loss. The lubricating properties, oxidation stability, and sensitivity to extreme-pressure antiwear agents of CTL are close to those of similar base oils. However, the sensitivity of CTL to typical antioxidants is relatively poor. In addition, compared with commercial PAO base oil, mPAO has a lower isomerization degree and fewer isomerization types. The oxidation stability and sensitivity to typical antioxidants of mPAO base oil are comparable with those of commercial PAO base oil, while its lubrication performance and sensitivity to typical extreme-pressure antiwear agents are significantly better than those of commercial PAO base oil.
The relationship between the structure characteristics and performances of coal based hydrogenation isomeric base oil (CTL) and metallocene catalyzed coal based polyalphaolefin (mPAO) base oil was clarified here. CTL and mPAO were compared with typical petroleum based and natural gas based commercial API Class III and IV base oils. Pressurized differential scanning calorimetry (PDSC), Rotary Bomb Oxidation Test (RBOT) and four-balls friction tester were used to evaluate the oxidation stability and lubrication performance of base oils under different working conditions. The sensitivity of different base oils to typical antioxidants and extreme pressure antiwear agents was compared. Specially, the composition and structure of CTL base oil are obviously different from GTL and mineral base oil. The coal-based CTL and mPAO base oils exhibit commendable viscosity-temperature properties, characteristics, coupled with low-temperature fluidity, fire safety, and minimal evaporation loss. The lubricating properties, oxidation stability and the sensitivity to extreme pressure antiwear agents of CTL are close to those of similar base oils. But the sensitivity of CTL to typical antioxidants is relatively poor. Besides, compared with commercial PAO base oil, mPAO has lower isomerization degree and fewer isomerization types. The oxidation stability and sensitivity to typical antioxidants of mPAO base oil are comparable with those of commercial PAO base oil, while its lubrication performance and sensitivity to typical extreme pressure antiwear agents are significantly better than those of commercial PAO base oil.