Multi-crop plants (fibrous hemp, maize, and faba bean) can potentially be an alternative to wood biomass pellets, but there is no detailed knowledge to support the suitability of this biomass for solid biofuel production. The aim of this study is to analyze and justify the suitability of multi-crop plant biomass for the production of biofuel pellets and to assess the environmental impact of burning them. This paper presents studies of physical-mechanical, thermal, and chemical characteristics of biofuel pellets from multi-crop plants and emissions during their combustion under laboratory conditions. The main parameters of the produced pellets were determined according to international standards, which are detailed in the methodology part. The length of the produced pellets ranged from 17.6 to 26.6 mm, and the diameter was about 6 mm. The density of wet pellets varied from 1077.67 to 1249.78 kg m−3. The amount of ash in the pellets varied from 5.75% to 8.02%. Determined lower calorific value of all pellets was close to 17.1 MJ kg−1. The lowest CO and CxHy emissions were determined when burning MIX2-1 pellets (biomass of the binary crop); their values were 572 and 29 ppm, respectively. The lowest content of CO2 was determined when burning S-Mz pellets (mono crop biomass), and it was 3.5%. The lowest NOx emissions were also determined when burning the pellets of this sample, with a value of 124 ppm. Research results show that multi-crop plants are a suitable raw material for the production of solid biofuel, the burning of which does not cause negative consequences for the environment.
Although wood biomass is mostly used to produce solid biofuel pellets, it is important to evaluate the possibilities of using other types of biomass as well. It is not only important to obtain biofuel pellets of suitable quality but also to ensure a sustainable process of producing and using these pellets for energy production. This paper presents an evaluation of the quality characteristics of seven different biofuel pellets made from multi-crop plants (fibrous hemp, maize, and faba bean) and a life cycle assessment (LCA) of the heat production by burning these pellets. The physical-mechanical properties and elemental composition of the pellets are determined according to international standards, as indicated in the methodology section. The LCA was performed using the SimaPro 9.5 software. The complete life cycle from cradle-to-grave is assessed, i.e., from growing plants to spreading ash obtained from pellet burning. An analysis showed that in most cases the produced pellets met the requirements of the standard ISO 17225-6:2021. The lowest negative environmental impact associated with the production of 1 GJ of thermal energy was for pellets made from fibrous hemp and maize biomass (MIX2-1) and pellets made from fibrous hemp and faba bean biomass (MIX2-3). Production of pellets from maize biomass (S-Mz) was found to have the highest carbon footprint (29.1 CO2eq GJ−1) and was associated with the lowest crop yield compared to the other six scenarios.
The article presents the results of a study on the preparation and use of faba bean waste and potato peel pellets for energy purposes. Physical and mechanical characteristics (moisture, density, ash content) of faba bean waste and potato peel pellets were investigated. The largest fraction of flour was formed on a sieve with 1 mm holes: faba bean waste—28.2 ± 2.02 g, potato peels—29.09 ± 0.73 g. For this experiment, samples were taken by mixing faba bean waste (four variants) and potato peel in the ratio of 1:1; 1:2; 1:3; 1:4 by volume (12 samples). It was found in this study that the density of pellets (DM) ranged from 1226.22 ± 13.88 kgm−3 to 1349.79 ± 6.79 kgm−3. The pellet moisture ranged from 6.70 ± 0.04% to 3.64 ± 0.13%. The lower calorific value of dry fuel pellets ranged from 15.27 ± 0.43 MJkg−1 to 16.02 ± 0.50 MJkg−1. The ash content of the pellets ranged from 8.05 ± 0.57% to 14.21 ± 0.05%. The ST temperature of the experimentally measured mixture of faba bean waste and potato peel pellets ranged from 924 to 969 °C; the DT temperature ranged from 944 to 983 °C; the HT temperature ranged from 1073 to 1202 °C, and a change in FT temperature from 1174 to 1234 °C was observed. The temperatures were sufficiently high to melt the ash. Specific emissions of CO2, CO, NOx and CxHy did not exceed the maximum levels allowed. In summary, from the results of the study of the physical properties, combustion, and emissions of waste beans and potato peel pellets (all samples), it is evident that they are used for biofuels. The combustion process of this type of pellet is characterized by efficient combustion and minimal emissions to the atmosphere.
This study investigates the combustion of agricultural biomass rich in alkali elements in the fluidized bed. The experiments were performed with smashed corn cob in a 500 kW fluidized bed combustor which was designed for work under low bed temperatures (650–700 °C). During the experiments, the formed compounds from corn cob combustion were measured by sampling particulate matter, and mineral compositions were determined. Also, the temperature profile of the FBC was established. It was determined that the emissions of K and Na elements from the FBC increased from 4 to 7.3% and from 1.69 to 3%, respectively, changing the bed temperature from 650 to 700 °C. Though alkali emissions are reduced at a 650 °C bed temperature, CO emissions are higher by about 50% compared to the case of 700 °C. The addition of 3% of dolomite reduced the pollutant emissions and alkali emissions as well. Potassium content decreased by about 1% and 4%, respectively, at the bed temperatures of 650 °C and 700 °C. The NOx emissions were less than 300 mg/m3 and did not exceed the limit for medium plants regarding DIRECTIVE (EU) 2015/2193. During extended experiments lasting 8 h, no agglomeration of the fluidized bed was observed. Moreover, the proposed configuration of the FBC and its operational parameters prove suitable for facilitating the efficient combustion of agricultural biomass.
The present study investigates the suitability of the invasive herbaceous species Sosnowsky’s hogweed (Heracleum sosnowskyi) and giant knotweed (Fallopia sachalinensis), together with reed (Phragmites australis), as feedstock for pressed biofuel pellets used alone and as additives to pinewood. Biomass of the three herbaceous species and pinewood was harvested, dried, chopped, milled, and pelletized through a 6 mm die to obtain pure pellets and binary mixtures of each herbaceous biomass with pinewood (25, 50, and 75% by weight of herbaceous share). The pellets were characterized for physical and mechanical properties, elemental composition, calorific value, combustion emissions, and life cycle impacts per 1 GJ of heat. Pellet density ranged from 1145.60 to 1227.47 kg m−3, comparable to or higher than pinewood, while compressive resistance satisfied solid biofuel quality requirements. The lower calorific values of all herbaceous and mixed pellets varied between 16.29 and 17.78 MJ kg−1, with increased ash and nitrogen contents at higher herbaceous shares. Combustion tests showed substantially higher CO and NOx emissions for pure invasive and reed pellets than for pinewood, but all values remained within national regulatory limits. Life cycle assessment indicated the highest global warming and fossil fuel depletion potentials for reed systems, followed by Sosnowsky’s hogweed and giant knotweed, with pinewood consistently exhibiting the lowest impacts. Overall, invasive plants and reed are technically suitable as partial pinewood substitutes in pellet production, supporting simultaneous invasive biomass management and renewable heat generation.
21 October 2026 in Plant Physiology and Biochemistry
Contamination with As, Cd and Pb can limit tree establishment on degraded substrates, but family-level variation in Scots pine responses remains poorly resolved. This study evaluated three open-pollinated maternal half-sib families of Pinus sylvestris L. under controlled hydroponic exposure to As, Cd and Pb. Growth, photosynthetic pigments, soluble sugars, phenolic and flavonoid contents, malondialdehyde, antioxidant enzyme activities, elemental composition and metal(loid) accumulation indices were analysed, with PCA and Random Forest used as exploratory integrative tools. Significant family and treatment interactions were observed for all measured physiological and biochemical traits, indicating non-uniform responses among families. Cd produced the clearest toxicity profile, characterized by strong chlorophyll (up to -56.0%) and carotenoid (up to -52.6%) losses, increased lipid peroxidation (up to +70.9%) and marked Fe, Mn and Zn disruption. Pb was retained predominantly in roots (up to 12.96 ± 0.45 g/kg DW), with very low translocation to shoots, but high Pb exposure strongly inhibited root elongation (up to -70.5%). As caused comparatively moderate pigment effects but was associated with increased S (up to +147.4%) and changes in secondary-metabolite and antioxidant traits. No family showed consistently superior performance across all metal(loid)s, although response strategies differed. These results identify integrated physiological and elemental screening of Scots pine reproductive material for phytostabilization-oriented restoration as potentially relevant, while field validation under realistic contaminated-substrate conditions before practical application remains necessary.