The present article focuses on pressed biofuel preparation from invasive herbaceous plants, and the quality indicators and properties were analyzed and determined. Two invasive herbaceous plants were chosen for this research: giant knotweed (Fallopia sachalinensis) and Sosnowsky’s hogweed (Heracleum sosnowskyi). For a control, pine wood biomass was utilized. After harvesting and drying, plant biomass was chopped and milled and later pressed into cylindrical pellets and briquettes. The research results for the pellets’ and briquettes’ physical and elemental properties showed that the density of the pellets (moisture 5–8%) reached 1145.60–1227.47 kg m−3, and the average density of the briquettes reached 615.60–867.31 kg m−3. The determined critical compressive strength of the pellets ranged from 420 N to 676 N, and the briquettes disintegrated under a significantly greater critical force of 783 N to 1219 N. The variation in pellet compressive strength with changes in their moisture content was also investigated. The determined lower caloric value of the pellets varied from 15.9 MJ kg−1 to 18.6 MJ kg−1. Harmful gas emissions during burning of the tested biofuel pellets were also evaluated and determined, and they were sufficiently low and did not exceed the permissible values. Finally, it can be stated that all of the pressed biofuels produced from invasive herbaceous plants met the most important requirements for the quality of pressed solid biofuel and can be used for burning in special boilers.
The present study investigates the suitability of the invasive herbaceous species Sosnowsky’s hogweed (Heracleum sosnowskyi) and giant knotweed (Fallopia sachalinensis), together with reed (Phragmites australis), as feedstock for pressed biofuel pellets used alone and as additives to pinewood. Biomass of the three herbaceous species and pinewood was harvested, dried, chopped, milled, and pelletized through a 6 mm die to obtain pure pellets and binary mixtures of each herbaceous biomass with pinewood (25, 50, and 75% by weight of herbaceous share). The pellets were characterized for physical and mechanical properties, elemental composition, calorific value, combustion emissions, and life cycle impacts per 1 GJ of heat. Pellet density ranged from 1145.60 to 1227.47 kg m−3, comparable to or higher than pinewood, while compressive resistance satisfied solid biofuel quality requirements. The lower calorific values of all herbaceous and mixed pellets varied between 16.29 and 17.78 MJ kg−1, with increased ash and nitrogen contents at higher herbaceous shares. Combustion tests showed substantially higher CO and NOx emissions for pure invasive and reed pellets than for pinewood, but all values remained within national regulatory limits. Life cycle assessment indicated the highest global warming and fossil fuel depletion potentials for reed systems, followed by Sosnowsky’s hogweed and giant knotweed, with pinewood consistently exhibiting the lowest impacts. Overall, invasive plants and reed are technically suitable as partial pinewood substitutes in pellet production, supporting simultaneous invasive biomass management and renewable heat generation.
The technology of invasive herbaceous plant harvesting and pressing biofuel preparation are the main topics of the article, and the quality indicators and attributes have been examined and identified. For this study, two types of invasive plants were used: Sosnowsky's hogweed (Heracleum sosnowskyi) and giant knotweed (Fallopia sachalinensis). Pine wood biomass was used as a control. This plant material was collected, dried, and put to use in the creation of pressed biofuel. Plant biomass was cut, processed, and then compressed into cylindrical briquettes after being harvested and dried. The average density of briquettes was found to range between 615.60 and 867.31 kg m-3 after examination of their physical and elemental parameters. The briquettes' determined critical compressive strength was found to disintegrate when subjected to a critical force between 783 N and 1219 N. Briquettes estimated lower calorific value was from 15.90 to 18.60 MJ kg-1. The test biofuel briquettes' harmful gas emissions were also assessed, and it was found that they were within acceptable limits and adequately low. In summary, it can be argued that all produced compressed biofuel from invasive plants complied with the majority crucial solid biofuel standards. Briquettes made from research plants can be burned in boilers designed for biofuel briquettes.
About Me
Lithuanian student specializing in biomass engineering
Lithuanian student specializing in biomass engineering