Sensitivity is a key parameter for microspeakers, especially in low-power applications such as consumer electronics, medical devices and Internet of Things. However, the sensitivities of most reported piezoelectric MEMS speakers are inferior to those of commercially available electrodynamic speakers. Design of high-sensitivity piezoelectric MEMS speakers requires an analytical expression of sensitivity, which is not yet available. In this paper, the analytical expression is derived, and an ultrahigh-sensitivity piezoelectric MEMS speaker is designed, fabricated and characterized. The sensitivities of the speaker in an ear simulator are 107 dB/mW, 104 dB/mW and 105 dB/mW at 250 Hz, 1 kHz and 10 kHz, respectively, which are the highest among piezoelectric MEMS speakers. The analytical calculation results and measurement data are perfectly matched. Furthermore, the speaker is based on thin-film AlN instead of commonly used thin-film PZT. This work demonstrates that the ultrahigh-sensitivity piezoelectric AlN MEMS speaker consumes 10 times less power than a typical 6 mm electrodynamic speaker; and the developed analytical expressions provide valuable design insights into piezoelectric MEMS speakers for high sensitivity and low power. [2022-0063]

This article proposes a novel structured aluminum nitrate (AlN) thin film based piezoelectric micromachined ultrasonic transducer (PMUT) with superior ultrasonic performances that can directly be applied for pulse-echo imaging. The bottom electrode of the PMUT is thickened and serves both as the electrical layer and supporting layer. Large numbers of elements are parallelly connected to form square arrays. This method can not only improve the acoustic output but also reduce the total impedance. The ultrasonic transmitting, receiving behaviors of our developed 6.37 MHz (in air) PMUT array containing vibration elements of horizontal × vertical = 20 × 20 are investigated. It can generate superior acoustic output with a normalized value of 1.71 kPa·V-17mm-2 at 3.6 mm away in deionized water media. Thanks to the lager acoustic output and reduced electrical impedance, ultrasonic pulse-echo imaging with our developed PMUT array is realized only with the assistance of a switch to separate the ultrasound transmission and reception process. We have mechanically scanned a mark in steel plate and generate a B-mode image with great accuracy using the recorded pulse-echo signals. These demonstrate the superior acoustic behavior of our developed PMUT array and open an avenue to the development of portable ultrasonic imaging devices.

Wireless power transfer is one of the enabling technologies for powering implantable biomedical devices. Biocompatibility and CMOS compatibility of wireless power transfer devices are highly desired due to safety and footprint concerns. Toward implantable applications, this paper presents an ultrasound-induced wireless power supply based on AlN piezoelectric micromachined ultrasonic transducer (PMUT). The wireless power supply integrates wireless power transfer, power management and energy storage functions. The PMUT array is used as a passive wireless power receiver, followed by electrical impedance matching networks and a voltage multiplier for efficient power transmission and rectification. The output power intensity of the wireless receiver reaches 7.36 μW/mm²with an incident ultrasound power below the FDA safety limit. The output power of the wireless power supply reaches 18.8 μW and a 100-μF capacitor is fully charged to 3.19 V after power management, which are sufficient to power many low-power implantable biomedical devices such as for neural electrical stimulation, biosensors and intrabody communication applications. The wireless power supply is implemented in a PCB with a diameter of 1 cm. With biocompatibility and CMOS compatibility of AlN thin film compared to commonly used PZT, the proposed solution paves the way for safer and ultraminiaturized wireless power supplies with further development incorporating all the functions on a monolithic chip in the future.

In this paper, a 2.6 GHz air-gap type thin film piezoelectric MEMS resonator was fabricated on a flexible polyethylene terephthalate film. A fabrication process combining transfer printing and hot-embossing was adopted to form a free-standing structure. The flexible radio frequency MEMS resonator possesses a quality factor of 946 and an effective coupling coefficient of 5.10%, and retains its high performance at a substrate bending radius of 1 cm. The achieved performance is comparable to that of conventional resonators on rigid silicon wafers. Our demonstration provides a viable approach to realizing universal MEMS devices on flexible polymer substrates, which is of great significance for building future fully integrated and multi-functional wireless flexible electronic systems.