Many applications in the area of location-based services and personal navigation require nowadays the location determination of a user not only in an outdoor environment but also an indoor. Typical applications of location-based services (LBS) mainly in outdoor environments are fleet management, travel aids, location identification, emergency services and vehicle navigation. LBS applications can be further extended if reliable and reasonably accurate three-dimensional positional information of a mobile device can be determined seamlessly in both indoor and outdoor environments. Current geolocation methods for LBS may be classified as GNSS-based, cellular network-based or their combinations. GNSS-based methods rely very much on the satellite visibility and the receiver-satellite geometry. This can be very problematic in dense high-rise urban environments and when transferring to an indoor environment. Especially, in cities with many high-rise buildings, the urban canyon will greatly affect the reception of the GNSS signals. Moreover, positioning in the indoor/outdoor transition areas would experience signal quality and signal reception problems, if GNSS systems alone are employed. The authors have proposed the integration of GNSS with wireless positioning techniques such as WiFi and UWB. In the case of WiFi positioning, the so-called fingerprinting method based on WiFi signal strength observations is usually employed. In this article, the underlying technology is briefly reviewed, followed by an investigation of two WiFi-positioning systems. Testing of the system is performed in two localisation test beds, one at the Vienna University of Technology and another one at the Hong Kong Polytechnic University. The first test showed that the trajectory of a moving user could be obtained with a standard deviation of about ±3–5 m. The main disadvantage of WiFi fingerprinting, however, is the required time consuming and costly signal strength system calibration in the beginning. Therefore, the authors have investigated if the measured signal strength values can be converted to the corresponding range to the access point. A new approach for this conversion is presented and analysed in typical test scenarios.

The increasing demand for clean and reliable water resources, coupled with the growing threat of water pollution, has made real-time water quality (WQ) monitoring and assessment a critical priority in many urban areas. Urban environments encounter substantial challenges in maintaining WQ, driven by factors such as rapid population growth, industrial expansion, and the impacts of climate change. Effective real-time WQ monitoring is essential for safeguarding public health, promoting environmental sustainability, and ensuring adherence to regulatory standards. The rapid advancement of Internet of Things (IoT) sensor technologies and smartphone applications presents an opportunity to develop integrated platforms for real-time WQ assessment. Advances in the IoT provide a transformative solution for WQ monitoring, revolutionizing the way we assess and manage our water resources. Moreover, recent developments in Location-Based Services (LBSs) and Global Navigation Satellite Systems (GNSSs) have significantly enhanced the accessibility and accuracy of location information. With the proliferation of GNSS services, such as GPS, GLONASS, Galileo, and BeiDou, users now have access to a diverse range of location data that are more precise and reliable than ever before. These advancements have made it easier to integrate location information into various applications, from urban planning and disaster management to environmental monitoring and transportation. The availability of multi-GNSS support allows for improved satellite coverage and reduces the potential for signal loss in urban environments or densely built environments. To harness this potential and to enable the seamless integration of the IoT and LBSs for sustainable WQ monitoring, a systematic literature review was conducted to determine past trends and future opportunities. This research aimed to review the limitations of traditional monitoring systems while fostering an understanding of the positioning capabilities of LBSs in environmental monitoring for sustainable urban development. The review highlights both the advancements and challenges in using the IoT and LBSs for real-time WQ monitoring, offering critical insights into the current state of the technology and its potential for future development. There is a pressing need for an integrated, real-time WQ monitoring system that is cost-effective and accessible. Such a system should leverage IoT sensor networks and LBSs to provide continuous monitoring, immediate feedback, and spatially dynamic insights, empowering stakeholders to address WQ issues collaboratively and efficiently.

In the work package ‘Integrated Positioning’ of the Ubiquitous Cartography for Pedestrian Navigation project (UCPNAVI) alternative location methods using active Radio Frequency Identification (RFID) are investigated for positioning of pedestrians in areas where no GNSS position determination is possible due to obstruction of the satellite signals. In most common RFID applications, positioning is performed using cell-based positioning. RFID tags can be installed at active landmarks (i.e., known locations) in the surroundings and a user equipped with an RFID reader can be positioned using Cell of Origin (CoO). The positioning accuracy, however, depends on the size of the cell defined by the maximum range of the signal. Using long range RFID for positioning the cell size can be quite large, i.e., around 20 m. Therefore, the paper proposes two new methods for positioning, i.e., trilateration and location fingerprinting based on received signal strength indication (RSSI) if more than one RFID tag is visible. The trilateration approach is based on the deduction of ranges to the RFID tags from RSSI. An iterative approach to model the signal propagation will be introduced, i.e., the International Telecommunication Union (ITU) indoor location model that can be simplified to a logarithmic model, and a simple polynomial model is employed for the signal strength to range conversion. In a second attempt, location fingerprinting based on RSSI is investigated. In this case, RSSI is measured in a training phase at known locations inside the building and stored in a database. In the positioning phase these measurements are used together with the current measurements to obtain the current location of the user. For the estimation of the current location different approaches are employed and tested, i.e., a direction-based approach, a tag-based approach, a direction-tag-based approach and a heading-based approach. Using trilateration or fingerprinting positioning accuracies on the one to a few metres level can usually be achieved. The concept and the iterative approach of the different methods and test results are discussed in this paper.

The availability of global navigation satellite systems (GNSS) on consumer devices has caused a dramatic change in every-day life and human behaviour globally. Although GNSS generally performs well outdoors, unavailability, intentional and unintentional threats, and reliability issues still remain. This has motivated the deployment of other complementary sensors in such a way that enables reliable positioning, even in GNSS-challenged environments. Besides sensor integration on a single platform to remedy the lack of GNSS, data sharing between platforms, such as in collaborative positioning, offers further performance improvements for positioning. An essential element of this approach is the availability of internode measurements, which brings in the strength of a geometric network. There are many sensors that can support ranging between platforms, such as LiDAR, camera, radar, and many RF technologies, including UWB, LoRA, 5G, etc. In this paper, to demonstrate the potential of the collaborative positioning technique, we use ultra-wide band (UWB) transceivers and vision data to compensate for the unavailability of GNSS in a terrestrial vehicle urban scenario. In particular, a cooperative positioning approach exploiting both vehicle-to-infrastructure (V2I) and vehicle-to-vehicle (V2V) UWB measurements have been developed and tested in an experiment involving four cars. The results show that UWB ranging can be effectively used to determine distances between vehicles (at sub-meter level), and their relative positions, especially when vision data or a sufficient number of V2V ranges are available. The presence of NLOS observations is one of the principal factors causing a decrease in the UWB ranging performance, but modern machine learning tools have shown to be effective in partially eliminating NLOS observations. According to the obtained results, UWB V2I can achieve sub-meter level of accuracy in 2D positioning when GNSS is not available. Combining UWB V2I and GNSS as well V2V ranging may lead to similar results in cooperative positioning. Absolute cooperative positioning of a group of vehicles requires stable V2V ranging and that a certain number of vehicles in the group are provided with V2I ranging data. Results show that meter-level accuracy is achieved when at least two vehicles in the network have V2I data or reliable GNSS measurements, and usually when vehicles lack V2I data but receive V2V ranging to 2–3 vehicles. These working conditions typically ensure the robustness of the solution against undefined rotations. The integration of UWB with vision led to relative positioning results at sub-meter level of accuracy, an improvement of the absolute positioning cooperative results, and a reduction in the number of vehicles required to be provided with V2I or GNSS data to one.

Recently new location technologies have emerged that can be employed in modern advanced navigation systems. They can be employed to augment Global Navigation Satellite System (GNSS) positioning techniques and dead reckoning as they offer different levels of positioning accuracies and performance. An integration of other technologies is especially required in indoor and outdoor-to-indoor environments. The paper gives an overview of the newly developed ubiquitous positioning technologies and their integration in navigation systems. Furthermore two case studies are presented, i.e., the improvement of land vehicle safety using Augmented Reality (AR) technologies and pedestrian navigation services for the guidance of users to certain University offices. In the first case study the integration of map matching into a Kalman filter approach is performed (referred to as “Intelligent Vehicle Navigation”) and its principle is briefly described. This approach can also be adapted for the pedestrian navigation service described in the second case study.

A variety of positioning systems have emerged for indoor localization which are based on several system strategies, location methods, and technologies while using different signals, such as radio frequency (RF) signals. Demands regarding positioning in terms of performance, robustness, availability and positioning accuracies are increasing. The overall goal of indoor positioning is to provide GNSS-like functionality in places where GNSS signals are not available. Analysis of the state-of-the-art indicates that although a lot of work is being done to combine both the outdoor and indoor positioning systems, there are still many problems and challenges to be solved. Most people moving on the city streets and interiors of public facilities have a smartphone, and most professionals working in public facilities or construction sites are equipped with tablets or smartphone devices. If users already have the necessary equipment, they should be provided with further functionalities that will help them in day-to-day life and work. In this review study, user requirements and the state-of-the-art in system development for smartphone localization are discussed. In particular, localization with current and upcoming ‘signals-of-opportunity’ (SoP) for use in mobile devices is the main focus of this paper.