Daiji Morita

Mr. Daiji Morita


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
Verified
Journal Article
Open access
PDF file
KMKeita Marumoto
Keita Marumoto
THTakahiro Horai
Takahiro Horai
DMDaiji Morita
Daiji Morita
COChisako Oda
Chisako Oda
TFTakafumi Fujii
Takafumi Fujii
MYMotomichi Yamamoto
Motomichi Yamamoto
The formation of brittle intermetallic compounds (IMCs) at the interface between dissimilar materials causes considerable problems. In this study, a multi-material additive manufacturing technique that employs a diode laser and the hot-wire method was developed for stainless steel/aluminum alloys. An Al-Mg aluminum alloy filler wire (JIS 5183-WY) was fed on an austenitic stainless-steel plate (JIS SUS304) while varying the laser power and process speed and using paste-type flux and flux-cored wire. The effects of laser power and process speed on phenomena during manufacturing and IMC formation were investigated. Finally, the wall-type multilayer specimens were fabricated under optimized conditions. The suppression of IMC formation to a thickness of less than 2 μm was achieved in the specimens, along with a high interfacial strength of over 120 MPa on average.

11 April 2025 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
DMDaiji Morita
Daiji Morita
NSNobuyuki Sumi
Nobuyuki Sumi
TSTakeshi Sakata
Takeshi Sakata
STShigeru Takushima
Shigeru Takushima
TMToshiya Matozaki
Toshiya Matozaki
RMRyuji Morita
Ryuji Morita
Additive manufacturing (AM) is widely applied due to its ability to produce precision components with complex geometries. In particular, 5000 series aluminum alloys, known for corrosion resistance, weldability, and workability, are considered promising materials for AM. However, aluminum alloys present challenges for high-quality, high-resolution manufacturing due to their high thermal conductivity and low viscosity, leading to porosity formation. Achieving both quality and resolution enables reduces post-processing time and improvement of efficiency. In the present study, a wire-laser metal 3D printer was employed to address these challenges by investigating the optimal fabrication conditions. Thin walls were fabricated under three laser power settings to examine heat input effects on quality and resolution. The results revealed that heat input plays a significant role in determining both the quality and resolution of the fabricated objects, and the mechanism responsible for thickness variation was also explained. Precise heat management is crucial for achieving high-quality and high-resolution manufacturing. Based on these insights, a method was demonstrated using initial high laser output to accumulate heat, then reducing output to control thickness, improve resolution, and maintain quality. As a result, high-quality, high-resolution structures with an average thickness of 3.4 mm, tensile strength ranging from 285 to 292 MPa, and anisotropy of 0.17% were successfully fabricated.

3 February 2026 in Progress in Additive Manufacturing
Verified
Journal Article
Open access
PDF file
DMDaiji Morita
Daiji Morita
NSNobuhiro Shinohara
Nobuhiro Shinohara
STShigeru Takushima
Shigeru Takushima
NSNobuyuki Sumi
Nobuyuki Sumi
TNTakayuki Nakagawa
Takayuki Nakagawa
RMRyuji Morita
Ryuji Morita
High-quality fabrication from aluminum alloys using a wire-laser metal 3D printer requires precise dimensional control, particularly uniform wall thickness. However, heat accumulation during the process poses a significant challenge. The present study aims to develop and validate a laser power control strategy that compensates for the effects of heat accumulation to achieve high-precision thickness control. To this end, an empirical model was developed based on a scaling law between build height and laser power. Laser power was then adjusted as a function of build height according to the model’s predictions. As a result, the proposed control strategy successfully maintained the target wall thicknesses (2.70, 2.80, and 2.90 mm), achieving an average deviation of 0.06 mm and a standard deviation of 0.11 mm, demonstrating effective dimensional control. Furthermore, optimizing the wire feeding conditions significantly reduced surface waviness—an issue that emerged after achieving dimensional control. In conclusion, this study presents a practical approach for high-precision dimensional control through model-based regulation and emphasizes the importance of integrated thermal input and material supply management for high-quality fabrication.