Keita Marumoto

Dr. Keita Marumoto


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 October 2024 in Welding in the World
Verified
Journal Article
Open access
PDF file
KMKeita Marumoto
Keita Marumoto
YSY. Sato
Y. Sato
AFA. Fujinaga
A. Fujinaga
TTT. Takahashi
T. Takahashi
HYH. Yamamoto
H. Yamamoto
MYMotomichi Yamamoto
Motomichi Yamamoto
In this study, an image-based method was developed for hot-wire laser narrow gap welding. The welding process was monitored based on image information processed using semantic segmentation, a method of classifying images by pixel. To control the welding position, an experimental system was configured that automatically follows the welding position by recognizing the position of the welding groove from the image during welding. In monitoring weld defects, a method was developed to predict the lack of fusion occurring on the wall surface using brightness information near the wall surface. For the lack of fusion occurring at the bottom of the groove, a defect detection method was developed by monitoring the molten pool shape using semantic segmentation. Defects were generated by intentionally reducing the laser power, and the defects were monitored from images taken during processing. In the unstable state where the laser power was reduced, the shape in front of the molten pool became unstable, and the occurrence of defects was monitored by capturing the shape change. In conclusion, this research made it possible to control and monitor the welding process with a single camera.

Verified
Journal Article
Open access
PDF file
KMKeita Marumoto
Keita Marumoto
THTakahiro Horai
Takahiro Horai
DMDaiji Morita
Daiji Morita
COChisako Oda
Chisako Oda
TFTakafumi Fujii
Takafumi Fujii
MYMotomichi Yamamoto
Motomichi Yamamoto
The formation of brittle intermetallic compounds (IMCs) at the interface between dissimilar materials causes considerable problems. In this study, a multi-material additive manufacturing technique that employs a diode laser and the hot-wire method was developed for stainless steel/aluminum alloys. An Al-Mg aluminum alloy filler wire (JIS 5183-WY) was fed on an austenitic stainless-steel plate (JIS SUS304) while varying the laser power and process speed and using paste-type flux and flux-cored wire. The effects of laser power and process speed on phenomena during manufacturing and IMC formation were investigated. Finally, the wall-type multilayer specimens were fabricated under optimized conditions. The suppression of IMC formation to a thickness of less than 2 μm was achieved in the specimens, along with a high interfacial strength of over 120 MPa on average.

10 February 2023 in Welding in the World
Verified
Journal Article
Closed access
PDF file
KMKeita Marumoto
Keita Marumoto
HTH. Tamata
H. Tamata
AFA. Fujinaga
A. Fujinaga
TTT. Takahashi
T. Takahashi
HYH. Yamamoto
H. Yamamoto
MYMotomichi Yamamoto
Motomichi Yamamoto

Verified
Journal Article
Open access
PDF file
KMKeita Marumoto
Keita Marumoto
AFAkira Fujinaga
Akira Fujinaga
TTTakeshi Takahashi
Takeshi Takahashi
HYHikaru Yamamoto
Hikaru Yamamoto
MYMotomichi Yamamoto
Motomichi Yamamoto
This study presents a new gas metal arc welding (GMAW) technique that achieves both high efficiency and low heat input using a hybridization of the hot-wire method. The optimal combination of welding speed and welding current conditions was investigated using a fixed hot-wire feeding speed of 10 m/min on a butt joint with a V-shaped groove using 19 mm thick steel plates. Molten pool stability and defect formation were observed using high-speed imaging and cross-sectional observations. The power consumption and heat input were predicted prior to welding and measured in the experiments. The results indicate that a combination of a welding current of 350–500 A and welding speed of 0.3–0.7 m/min is optimal to avoid defect formation and molten metal precedence using three or four passes. The higher efficiency and lower heat input achieved by hot-wire GMAW results in a weld metal of adequate hardness, narrower heat-affected zone, smaller grain size at the fusion boundary, and lower power consumption than those obtained using tandem GMAW and high-current GMAW. Based on the experimental results, a single bevel groove, which is widely used in construction machinery welding joints, was welded using hot-wire GMAW, and we confirmed that the welding part could be welded in six passes, whereas eight passes were required with GMAW only.

10 January 2025 in Materials
Verified
Journal Article
Open access
PDF file
JGJukkapun Greebmalai
Jukkapun Greebmalai
KMKazuyuki Matsumoto
Kazuyuki Matsumoto
KMKeita Marumoto
Keita Marumoto
MYMotomichi Yamamoto
Motomichi Yamamoto
Application of high-heat input welding on high-tensile strength steels causes deterioration of mechanical properties of the welded joint, due to softening and grain coarsening in the heat-affected zone (HAZ). In this study, low-heat input narrow-gap hot-wire laser welding was applied to 12 mm thick 780 MPa-class high-tensile strength steel plate. Conditions were optimized based on microstructural observations of joints produced at various welding speeds. Heat input was estimated from measured grain size. Evaluation of properties of joints welded at 0.5 m/min revealed sound toughness, tensile strength, and elongation. The effect of undermatched weld metal width on joint strength was analyzed using a finite element method. When the width of undermatched weld metal was 2.5 mm, the joint strength was 99% of the base metal strength; when it was 7.5 mm, the strength dropped to 95%. The effect of HAZ softening width on joint strength with even-matched weld metals was similarly analyzed, showing that even when the HAZ softening width was 2.0 mm, the joint strength was 98% of the base metal strength. The results of this study suggest that narrow-gap hot-wire laser welding can efficiently reduce heat input and the HAZ softening zone, thereby achieving both high strength and high toughness.

18 July 2025 in Metals
Verified
Journal Article
Open access
PDF file
JGJukkapun Greebmalai
Jukkapun Greebmalai
SSShun Sadasue
Shun Sadasue
KMKeita Marumoto
Keita Marumoto
EWEakkachai Warinsiriruk
Eakkachai Warinsiriruk
MYMotomichi Yamamoto
Motomichi Yamamoto
This study joins a 20 mm thick 5000-series aluminum alloy using hot-wire insertion combined with narrow-gap laser welding to evaluate the feasibility and welding characteristics of this technique. The findings indicate that weld formation is primarily influenced by the laser energy density and material deposition rate. A strategy for improving weld beads is introduced incorporating a reoriented laser spot during the final pass on narrow-gap joints. This approach improves penetration and produces defect-free joints. The optimal processing conditions result in complete joint formation with four welding passes. Microstructural analysis reveals that the aluminum matrix morphology evolves according to the local thermal history during welding. Measurements show that the weld region is slightly harder than the base metal, whereas slightly lower hardness is observed at the fusion line and inter-pass boundaries, which correlates with the microstructure result.