This article based on the standards IEC61967-8 and IEC62132-8 aims to provide a new method to expand the working bandwidth of the closed version IC-Stripline cell. By analyzing the working principle and discussing the limiting factors of the working bandwidth, this article presents the slotted septum method and the dielectric method to expand the working bandwidth of the IC-Stripline cell. A 3-D model of the IC-Stripline cell is established in the 3-D electromagnetic (EM) simulation software, and the $S$ -parameters and voltage standing wave ratio (VSWR) of the IC-Stripline cell are calculated. The calculation results show that the slotted septum method and the dielectric method can expand the working frequency band of the IC-Stripline cell from 0–6 to 0–7 and 0–11 GHz, respectively. The measurement results are consistent with the simulation results. In the end, the field uniformity is analyzed, and the results show that both methods have no significant impact on the field uniformity of the cell.
This paper models and analyzes the Complementary Metal Oxide Semiconductor (CMOS) cross-coupled differential-drive (CCDD) rectifier for Ultra-Low-Power ambient radio-frequency energy harvesters (RFEHs) working in the subthreshold region. In this paper, two closed-form equations of CCDD rectifier output voltage and input resistance in the subthreshold region were derived based on BSIM4 models of NMOS and PMOS. The model give insight to specify circuit parameters according to different inputs, transistor sizes, threshold voltages, numbers of stages, load conditions and compensation voltages, which can be used to optimize the rectifier circuit. There is a good agreement between the simulation results and these models, and these models have a maximum deviation of 10% in comparison with the simulation results in the subthreshold region. The measurement results of a single-stage CCDD rectifier reported in a previous paper were adopted to verify the model. The output voltage and input resistance predicted by these models provide excellent consistency with corresponding measurement results. The model can be employed to optimize the CCDD rectifier without expensive calculation in the design stage.
1 January 2017 in Proceedings of Meetings on Acoustics
Doppler scale estimation for underwater acoustic (UWA) communications is important yet challenging. Most Doppler scale estimators rely on training data or specially designed packet structures. These methods have fundamental limitations in transmission rate and spectral efficiency. Different from these methods, this paper presents a Doppler scale estimation approach exploiting the cyclostationarity of orthogonal frequency-division multiplexing (OFDM) signals. We analyze the cyclic features of cyclic prefix (CP) OFDM signals over doubly selective underwater channels in order to demonstrate the relationship between the cyclic features and the Doppler scale. Comparing with CP-OFDM signals, zero padding (ZP) OFDM signals have no redundant information contained within each block. Therefore, the proposed estimation method turns to be more significant for ZP-OFDM systems, which is usually used for underwater communication to save energy. Simulation results validate our theoretical analysis and the performance of the proposed Doppler scale estimator.
With the purpose of radiation emissions and immunity measurement of large size and high-frequency integrated circuits (ICs), three closed version IC-Stripline cells conforming to the IEC standardswere designed in this paper to expand the uniform field region and the working frequency band of the traditional IC-Stripline cell. In these cells, the long version IC-Stripline cell expands the 3 dB uniform field region of the traditional IC-Stripline cell from 3 × 3 cm to 3 × 8 cm, with the working bandwidth remaining as 6 GHz. The IC-Stripline cell based on image theory further expands the 3 dB uniform field region into two 3 × 8 cm areas with the working bandwidth unchanged. The third cell is a scaled-down IC-Stripline cell based on image theory, which can expand the working bandwidth from 6 GHz to 12 GHz and the total area of the uniform field region is equivalent to that of the traditional IC-Stripline cell.
This letter presents the design of dual-band high-efficiency transistor-based rectifiers, which employ class-F and inverse class-F modes at different operating frequencies. This alleviates the issue of inaccurate harmonic impedance control caused by a large frequency ratio, thereby effectively improving the rectification efficiency at the desired operating frequency. Then, to achieve dual-mode configuration at dual frequencies, the transistor-based class-F and class-F−1 self-synchronous rectifiers with variable phase shift are analyzed. This breaks through the limitations of the fixed phase shift required by traditional rectifiers for dual-mode configurations. For validation, a dual-band high-efficiency rectifier based on a GaN HEMT is designed, fabricated, and tested. Measurement results indicate that the realized rectifier has an input power capacity of at least 10 W with peak rectification efficiencies of 85.6% and 84.6% at 1.6 and 2.4 GHz, when the gate voltage is −3.5 V and the dc load is $70~\Omega $ .