Baldev Dogra

Baldev Dogra

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 December 2018 in Sugar Tech
Verified
Journal Article
Closed access
PDF file
MKMohit Kumar
Mohit Kumar
BDBaldev Dogra
Baldev Dogra
GSGulzar Singh Sanghera
Gulzar Singh Sanghera
GMGursahib Singh Manes
Gursahib Singh Manes

21 May 2024 in Sustainability
Verified
Journal Article
Open access
PDF file
NSNeeraj Kumar Singh
Neeraj Kumar Singh
BDBaldev Dogra
Baldev Dogra
GMGursahib Singh Manes
Gursahib Singh Manes
DPDilwar Singh Parihar
Dilwar Singh Parihar
Ali SalemAli Salem
Ali Salem
Ahmed ElbeltagiAhmed Elbeltagi
Ahmed Elbeltagi
This study was carried out to investigate the effect of the spading machine as a sustainable tillage tool at different depths of tillage on soil parameters. The spading machine was evaluated for two independent parameters: soil type and depth of cut. The observed dependent parameters were the bulk density of soil, mean clod size, soil strength, torque requirement, fuel consumption, and cost of operation. The bulk density varied from 1.18 to 1.39 g/cm3, the mean clod size between 12.72 and 68.37 mm, the soil strength between 69 and 4714.5 kPa, the torque requirement between 206 and 344.62 N-m, the fuel consumption between 13.60 and 21.83 l/ha, and cost of operation ranged between 2670.37 INR/ha (34.71 USD/ha) and 3635.87 INR/ha (47.27 USD/ha). It was observed that with the increase in tillage depth, the dependent parameters were also increasing, except the cost of operation varied nonsignificantly. In comparison to the spading machine, other primary tillage tools resulted in higher bulk density and fuel consumption, whereas mean clod size and cost of operation were reported higher except for the rotary tillage tool. Thus, the spading machine could be a sustainable tillage tool for long-term agricultural goals.

31 January 2019 in Legume Research - An International Journal
Verified
Journal Article
Open access
PDF file
BDBaldev Dogra
Baldev Dogra
DKDinesh Kumar
Dinesh Kumar
RDRitu Dogra
Ritu Dogra
ISInderjit Singh
Inderjit Singh
GMG.S. Manes
G.S. Manes
Pigeon-pea is very thick and woody stem crop, therefore the harvesting and threshing of this crop is a drudgery and time consuming. At present in India pigeon-pea is harvested manually with sickle and after that the crop is left in the field in the form of heaps for 7-10 days for sun drying. After sun drying the crop is threshed with suitable thresher or beating with stick etc. Lack of mechanization of harvesting and threshing operation is one of the limitations to the increase production and productivity of pigeon-pea. Therefore, the present study was aimed at optimizing operational and crop parameters influencing the mechanized harvesting and threshing of pigeon-pea crop with combine harvester. PAU-881, AL-1856, AL-1817 and AL-1811 of extra-short duration pigeon-pea were selected for the study. The moisture content of crop and grain varied from 38 to 48% and 22 to 25% on wet basis respectively for crop varieties AL-1817 and AL-1811 and it was 48 to 53% and 24 to 27% on wet basis respectively for crop varieties PAU-881 and AL-1856. Concave clearance was kept as 16 mm at front side and 7 mm from rear side. Threshing efficiency was more than 98% at cylinder peripheral speed of 26.61 m/s and 34.85 m/s in all varieties except PAU-881. The percent grain breakage was higher for higher cylinder peripheral speed and lower for higher forward speed. The grain damage was below 1% for 23.85m/s, 26.61 m/s and 34.85 m/s cylinder peripheral speed in all crop varieties except AL-1811. The optimum values of peripheral velocity and forward speed of combine harvester harvesting pigeon-pea were 26.61 m/s and 2.0 km/h for all selected varieties.

31 January 2019 in Legume Research - An International Journal
Verified
Journal Article
Open access
PDF file
BDBaldev Dogra
Baldev Dogra
DKDinesh Kumar
Dinesh Kumar
RDRitu Dogra
Ritu Dogra
TBT.S. Bains
T.S. Bains
GMG.S Manes
G.S Manes
The present study was aimed at optimizing operational and crop parameters influencing the mechanized harvesting and threshing of mung-bean crop with combine harvester. Two varieties of summer mung-bean SML-668 and SML-832 and one variety of kharif mung-bean ML-818 were selected for the study. Concave clearance was kept as 25 mm at front side and 10 mm from rear side. The height of cut the crop ranged from 8-9.5 cm. Threshing efficiency was more than 98% at cylinder peripheral speeds C3 and C4 in all varieties except SML-832. The percent grain damage was higher for higher cylinder peripheral speed and lower for higher forward speed. The grain damage ranged from 1.54 – 3.22 percent for C1, C2 and C3 cylinder peripheral speed in all crop varieties. Peripheral speed of 18.91 m/s and forward speed of 1.5 km/h was found to be optimum for harvesting mung-bean with combine harvester for all crop varieties.