Aylin Ahadi

Prof. Aylin Ahadi


Research Focus & Metrics

Academic Career Length

27Years (2000-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2013 in Procedia CIRP
Verified
Journal Article
Open access
LCLing Chen
Ling Chen
AAAylin Ahadi
Aylin Ahadi
JZJinming Zhou
Jinming Zhou
JSJan-Eric Ståhl
Jan-Eric Ståhl
Surface roughness is a commonly used criterion for characterization of surface quality in a machining operation. In the study of micro-scale mechanical properties of machined surface and cutting tool with nanoindentation, prefect surface finish on the test specimen is often required for the reliable result. However, the prefect surface finish is often difficult to obtain from the machining operation due to the limitation of the cutting tool geometry and machining dynamics. In presented paper, the effect of surface roughness on nanoindentation measurement was investigated by using finite element method. A 3D finite element model with three levels of surface roughness was developed to simulate the load-displacement indentation process with a Berkovich indenter. The material used in the simulation is AISI 316L stainless steel and it was modeled as an elastic-plastic von Misses material. Three levels of surface roughness, Ra, are used in the simulation, including 2nm, 20nm and 37nm. The mechanical properties were calculated by combined simulation with the Oliver-Pharr method. The hardness and reduced modulus from the simulation was found to decrease with an increase of roughness. The scatter of load-depth curves and deviation of hardness and reduced modulus are affected by the changing of roughness. The height of pile-up was little affected by the surface roughness from the simulation. Combined effect of indenter tip radius and surface roughness was also investigated

1 October 2014 in Mechanics of Materials
Verified
Journal Article
Closed access
MAMathias Agmell
Mathias Agmell
AAAylin Ahadi
Aylin Ahadi
JSJan-Eric Ståhl
Jan-Eric Ståhl

15 August 2016 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
MAMathias Agmell
Mathias Agmell
AAAylin Ahadi
Aylin Ahadi
OGOleksandr Gutnichenko
Oleksandr Gutnichenko
JSJan-Eric Ståhl
Jan-Eric Ståhl
The aim of this paper is to gain a better understanding of the impact different micro-geometries has on stress distribution in cutting tools. Both principal and effective stress distribution are studied. These quantities have a major impact on the occurrence of damages in the cutting tool such as crack formation, flaking, chipping, breakage and plastic deformation. The development of a stagnation zone is also investigated as well as the effect tool micro-geometries have on this zone. A finite element model is developed which enables the examination of these aspects, in detail. It was found that the model predicted these metal cutting phenomena with high accuracy. Cutting forces is within the standard deviation of experimental results. The experimental results also indicate that the stress distributions and the stagnation zone have been simulated correctly. This study has shown that the micro-geometries of the cutting tool have a great potential in reducing the maximal tensile/principal stress. This research work has also shown that the size of the stagnation zone can be controlled by micro-geometries on the cutting tool, which in turn can have an effect on the wear on the cutting edge.

26 February 2018 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
MAMathias Agmell
Mathias Agmell
VBVolodymyr Bushlya
Volodymyr Bushlya
SLSampsa Laakso
Sampsa Laakso
AAAylin Ahadi
Aylin Ahadi
JSJan-Eric Ståhl
Jan-Eric Ståhl
This paper presents the development of a FE-simulation model to predict the mechanical stresses and thermal loads that a cutting tool of polycrystalline cubic boron nitride (pcBN) is subjected to, when machining AISI 316L. The serrated chip formation of AISI 316L has a major impact on the periodic loads acting on the cutting tool. Therefore, it is vital to correctly model this serrated chip formation. One of the major difficulties with FE-simulations of metal cutting is that the extreme deformations in the workpiece material, often leads to a highly distorted mesh. This paper uses the Coupled Eulerian-Lagrangian (CEL) formulation in Abaqus/Explicit, where the workpiece is modelled with the Eulerian formulation and the cutting tool by the Lagrangian one. This CEL formulation enables to completely avoid mesh distortion. To capture the chip serration process, the workpiece material is described with the Johnson-Cook damage model. The FE-simulation results are validated via comparison of the modelled cutting forces, chip serration frequency, and contact length against experimental ones.

2 January 2017 in Machining Science and Technology
Verified
Journal Article
Closed access
MAM. Agmell
M. Agmell
AAAylin Ahadi
Aylin Ahadi
JZJ. M. Zhou
J. M. Zhou
RPR. L. Peng
R. L. Peng
VBV. Bushlya
V. Bushlya
JSJ.-E. Ståhl
J.-E. Ståhl
Traditionally, the development and optimization of the machining process with regards to the subsurface deformation are done through experimental method which is often expensive and time consuming. This article presents the development of a finite element model based on an updated Lagrangian formulation. The numerical model is able to predict the depth of subsurface deformation induced in the high- speed machining of Inconel 718 by use of a whisker-reinforced ceramic tool. The effect that the different cutting parameters and tool microgeometries has on subsurface deformation will be investigated both numerically and experimentally. This research article also addresses the temperature distribution in the workpiece and the connection it could have on the wear of the cutting tool. The correlation of the numerical and experimental investigations for the subsurface deformation has been measured by the use of the coefficient of determination, R2. This confirms that the finite element model developed here is able to simulate this type of machining process with sufficient accuracy.

1 January 2013 in Procedia CIRP
Verified
Journal Article
Open access
MAMathias Agmell
Mathias Agmell
AAAylin Ahadi
Aylin Ahadi
JSJan-Eric Ståhl
Jan-Eric Ståhl
In the present study the plasticity parameters in the Johnson Cook plasticity model are determined on the basis of process parameters in orthogonal cutting by use of inverse analysis. Previously established links between material parameters and process parameters in the cutting process such as chip thickness ratio, cutting forces, temperatures, deformation zones, is used serve as a starting point in the inverse analysis. The material AISI 4140 is simulated using the model employed in [1], the Johnson Cook parameters being changed within an interval of ±30%. The inverse analysis is performed using a Kalman filter. The material model for the reference point is validated on the basis of the experimental results in [1], the model being shown to predict the process parameters with a high level of accuracy. The attempt is made to establish a link for materials having cutting process characteristics that are similar between certain process parameters and the Johnson Cook parameters in order to be able to predict the input parameters to FEM models using experimental data from a cutting proces