Sampsa Laakso

Prof. Dr. Sampsa Laakso

orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2018 in Journal of Manufacturing Processes
Verified
Journal Article
Closed access
SLSampsa Laakso
Sampsa Laakso
MAMathias Agmell
Mathias Agmell
JSJan-Eric Ståhl
Jan-Eric Ståhl

23 November 2012 in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
Verified
Journal Article
Closed access
PDF file
JHJuha Huuki
Juha Huuki
SLSampsa Laakso
Sampsa Laakso
Ultrasonic burnishing is a relatively new method used for finishing workpieces to produce good surface quality. Ultrasonic burnishing does not involve material removal from the surface of the workpiece. However, the method has a significant deforming effect on the material, especially close to the surface, which is why it is vital to know the effect of the method to residual stresses in the material. This study looks at the residual stresses produced in two 34CrNiMo6-M tempering steel qualities of different hardness. The magnitude of stresses is examined using the hole drilling method. The hardness and surface quality of the finished workpiece are measured. The results show that the ultrasonic burnishing not only treats material on the surface efficiently but also deforms the material deeper, producing compressive residual stresses in the workpiece. The hardness increases after finishing and surface quality improves significantly. The roundness of the workpiece is improved and dimensional changes are minor.

29 February 2020 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
MAMathias Agmell
Mathias Agmell
VBVolodymyr Bushlya
Volodymyr Bushlya
RMRachid M’saoubi
Rachid M’saoubi
OGOleksandr Gutnichenko
Oleksandr Gutnichenko
OZOleg Zaporozhets
Oleg Zaporozhets
JSJan-Eric Ståhl
Jan-Eric Ståhl
This study investigates machining superalloy Inconel 718 with polycrystalline cubic boron nitride (pcBN) tooling both numerically and experimentally. Particular attention is given to mechanical and thermal stresses in the cutting tool arising from segmented chip formation and associated forces and temperatures. The temperature dependence of the mechanical properties of pcBN has been investigated and incorporated into a numerical model. In order to capture the dynamic loads due to a serrated chip formation, the Johnson–Cook damage model has been used. The extreme deformations during a machining process often results in a numerical difficulties due to a distorted elements. This paper uses the coupled Eulerian–Lagrangian (CEL) formulation in Abaqus/Explicit, where the workpiece is modelled with the Eulerian formulation and the cutting tool by the Lagrangian one. This CEL formulation enables to completely avoid mesh distortion. The finite element simulation results are validated via comparison of the modelled static and dynamic cutting forces and thermal loads induced into the cutting tool. The numerical model predicts a temperature of 1100–1200 ∘C at the cutting interface, which is in line with experimental determined data. The principal stresses at the rake up to 300 MPa are recorded, whereas higher level of stresses up to 450 MPa are found in the notch region of the tool, well correlated with experimental observation.

1 January 2017 in Procedia Manufacturing
Verified
Journal Article
Open access
ZTZhao Tao
Zhao Tao
SYShi Yaoyao
Shi Yaoyao
SLSampsa Laakso
Sampsa Laakso
ZJZhou Jinming
Zhou Jinming

26 February 2018 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
MAMathias Agmell
Mathias Agmell
VBVolodymyr Bushlya
Volodymyr Bushlya
SLSampsa Laakso
Sampsa Laakso
AAAylin Ahadi
Aylin Ahadi
JSJan-Eric Ståhl
Jan-Eric Ståhl
This paper presents the development of a FE-simulation model to predict the mechanical stresses and thermal loads that a cutting tool of polycrystalline cubic boron nitride (pcBN) is subjected to, when machining AISI 316L. The serrated chip formation of AISI 316L has a major impact on the periodic loads acting on the cutting tool. Therefore, it is vital to correctly model this serrated chip formation. One of the major difficulties with FE-simulations of metal cutting is that the extreme deformations in the workpiece material, often leads to a highly distorted mesh. This paper uses the Coupled Eulerian-Lagrangian (CEL) formulation in Abaqus/Explicit, where the workpiece is modelled with the Eulerian formulation and the cutting tool by the Lagrangian one. This CEL formulation enables to completely avoid mesh distortion. To capture the chip serration process, the workpiece material is described with the Johnson-Cook damage model. The FE-simulation results are validated via comparison of the modelled cutting forces, chip serration frequency, and contact length against experimental ones.

19 April 2020 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Open access
PDF file
RURizwan Ullah
Rizwan Ullah
Jan Sher AkmalJan Sher Akmal
Jan Sher Akmal
SLSampsa Laakso
Sampsa Laakso
ENEsko Niemi
Esko Niemi
Implementing additive manufacturing in an industry, particularly for critical applications of lightweight aluminum (AlSi10Mg), requires part properties that are both accurate and precise to conform to the intent of a robust design. In this experimental study, the objective was to evaluate anisotropy in part properties (i.e., flatness, surface roughness, surface porosity, surface hardness, pre-hole shrinkage, drilling thrust force, and thread-stripping force) when the part orientation (i.e., print inclination and recoater angle) was independently changed. This study developed and investigated an innovative procedure for determining anisotropy in part properties. The part properties were evaluated by designing specific features on a tailor-made flat plate. The replicas of the aluminum plate were additively manufactured at varying orientations using two commercial EOS parameter sets for the laser-based powder bed fusion technique. Conventional measurement equipment was used to analyze all the part properties, except the thread-stripping force, which was measured using a custom-made setup. All the part properties indicated a considerable degree of anisotropy, excluding the drilling thrust force. The printing parameters dictate the significance of the anisotropy. The anisotropy in flatness and pre-hole shrinkage decreases with an increased substrate temperature and a decrease in energy input and thermal gradient. The presence of surface overlapping contours in the scan strategy and an increased energy input can reduce anisotropy in surface roughness and hardness. No significant anisotropy was detected when the recoater angle was changed. This study helps designers establish and substantiate design for additive manufacturing that is within the limits of appropriate anisotropy for a robust design.