This study examined the impact of temperature optimization on indium tin oxide (ITO) films in monolithic HJT/perovskite tandem solar cells. ITO films were deposited using magnetron sputtering at temperatures ranging from room temperature (25 °C) to 250 °C. The sputtering target was ITO, with a mass ratio of In2O3 to SnO2 of 90% to 10%. The effects of temperature on the ITO film were analyzed using X-ray diffraction (XRD), spectroscopic ellipsometry, and sheet resistance measurements. Results showed that all ITO films exhibited a polycrystalline morphology, with diffraction peaks corresponding to planes (211), (222), (400), (440), and (622), indicating a cubic bixbyite crystal structure. The light transmittance exceeded 80%, and the sheet resistance was 75.1 Ω/sq for ITO deposited at 200 °C. The optical bandgap of deposited ITO films ranged between 3.90 eV and 3.93 eV. Structural and morphological characterization of the perovskite solar cell was performed using XRD and FE-SEM. Tandem solar cell performance was evaluated by analyzing current density-voltage characteristics under simulated sunlight. By optimizing the ITO deposition temperature, the tandem cell achieved a power conversion efficiency (PCE) of 16.74%, resulting in enhanced tandem cell efficiency.
15 June 2023 in Eurasian Journal of Science Engineering and Technology
This article presents an investigation into the structural, optical, and electrical properties of Indium Tin Oxide (ITO) films that were deposited utilizing various plasma powers. The transmittance values in the visible region were measured, revealing that the ITO film deposited at 2050 W exhibited the highest transmittance (81%). Additionally, the sheet resistance values of all films were analyzed, indicating that the ITO film deposited at 2050 W had the lowest sheet resistance (64.9 Ω/sq). By means of XRD analysis, the structural properties of the films were meticulously scrutinized, and the distinctive diffraction peaks associated with the ITO films were successfully identified. Notably, the ITO film deposited at 2050 W demonstrated superior performance compared to the other films deposited using various plasma powers. Finally, we report a noteworthy efficiency of 17.03% achieved in the SHJ solar cell fabricated with the ITO film deposited at 2050 W on a 5x5 cm2 n-type Si substrate.
15 December 2023 in Eurasian Journal of Science Engineering and Technology
This research focuses on using SCAPS-1D software to design and simulate efficient flexible perovskite solar cells. The study aims to optimize design parameters, gain a deeper understanding of the underlying physics, and obtain valuable insights into electrical characteristics. The device architecture includes key components like PET/ITO substrate, TiO2 ETL, CH3NH3SnI3 absorber, CuSCN HTL, and Au electrode. By optimizing the absorber thickness (600 nm) and temperature (300 K), the performance and efficiency of the cell were improved. Investigation of different doping concentrations at 300 K for a fixed thickness revealed an efficiency of 26.98% at 600 nm. The highest efficiency of 31.44% was achieved with a doping concentration of 1E+21. This research showcases the potential of flexible perovskite solar cells for lightweight and versatile applications, emphasizing their significance in the field.
31 January 2023 in Uluslararası Muhendislik Arastirma ve Gelistirme Dergisi
Yüksek verimli perovskit güneş hücresi elde etmek için pin hole içermeyen, ince, yüksek şeffaflı, mükemmel taşıyıcı ayırma kabiliyetine sahip, üretimi kolay elektron transfer tabakasına (ETL) olması gereklidir. ETL malzemesi olarak hem kompakt (c-TiO2) hem de mezo (mp-TiO2) yapılı olarak kullanılabilen TiO2’dir. Bu çalışmada üretilen ETL, c-TiO2’in sol-jel yöntemiyle hazırlanmış 2000, 2500, 3000, 3500 ve 4000 rpm beş farklı döneme hızlarında döndürülerek kaplama yöntemiyle kaplanmıştır. Kaplanan incefilmlerden perovskit güneş hücreleri için en ideal kalınlıkta, pin hole içermeyen aktif kristalli elektron transfer tabakası belirlenerek SEM, XRD ve profilometre yardımıyla karakterize edilmiştir.
27 June 2024 in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
Photovoltaics offer a sustainable solution for the growing energy needs of the world, while reducing environmental impact. Transparent Conductive Oxides (TCOs), which are essential in photovoltaic technology, offer high light transmittance and effective charge carrier extraction. This research focuses on the impact of oxygen (O2) flow rates in the deposition of indium tin oxide (ITO) films on n-type crystalline silicon (c-Si) substrates by DC magnetron sputtering. The structural, optical, and electrical properties were analyzed. Based on the results, the optimal O2 ratio was determined and used in the fabrication of SHJ solar cells, achieving an efficiency of 18.6%.