Liangliang Ding

Prof. Liangliang Ding

National University of Defense Technology, Changsha, Guangdong, China
orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 January 2019 in Polymers
Verified
Journal Article
Open access
PDF file
LDLiangliang Ding
Liangliang Ding
JZJingyuan Zhou
Jingyuan Zhou
WTWenhui Tang
Wenhui Tang
XRXianwen Ran
Xianwen Ran
YHYuxuan Hu
Yuxuan Hu
Metal/polymer reactive materials have been studied and applied in a wide range of ways in recent years. This type of material is insensitive under normal conditions but reacts violently and releases a large amount of chemical energy under high-speed impact or high strain rate loading conditions. Compared with conventional explosives, it has better mechanical properties, and its unit mass energy is several times that of TNT. In this paper, PTFE/Al/CuO reactive materials are the main research objects, and we assess the impact energy release abilities of this type of reactive material through experimental research. To this end, eight sets of material formulations are designed, and the effects of particle size, the ratio of PTFE/Al and Al/CuO materials, and sintering on the energy release ability of the reactive materials are investigated. All experiments are carried out based on a self-designed new energy release testing device. The experimental device can measure the pressure time history curve generated by the reactive materials, and the rationality of the pressure time history curve can also be verified by the displacement time curve of the piston. The results show that with an increase in the Al/CuO thermite content, the energy release rate of the reactive material clearly increases, which is attributed to the reaction threshold of Al/CuO being low and because the heat generated can promote the reaction of PTFE/Al. The energy release rate of the nano-scale reactive materials is higher than that of the micron-scale reactive materials because the reduction in particle size results in a larger specific surface area. Thus, the energy required for ignition is lower. The energy release rate of sintered reactive materials is higher than that of unsintered reactive materials, which can be explained by the interfacial area between Al particles and PTFE particles in sintered reactive materials being larger, which makes the reaction more sufficient. The self-designed energy release testing device for the reactive materials and the conclusions obtained in this paper have clear significance for guiding engineering applications.

4 January 2018 in Materials
Verified
Journal Article
Open access
PDF file
LDLiangliang Ding
Liangliang Ding
WTWenhui Tang
Wenhui Tang
XRXianwen Ran
Xianwen Ran
The shaped charge tandem warhead is an effective weapon against the ERA (explosive reactive armor). Whether the pre-warhead can reliably initiate the ERA directly determines the entire performance of the tandem warhead. The existing shaped charge pre-warhead mostly adopts a metal shaped jet, which effectively initiates the ERA, but interferes the main shaped jet. This article, on the other hand, explores the possibility of producing a pre-warhead using a low-density material as the liner. The nonlinear dynamic analysis software Autodyn-2D is used to simulate and compare three kinds of low-density shaped jets, including floatglass, Lucite, and Plexiglas, to the copper shaped jet in the effectiveness of impacting ERA. Based on the integrative criteria (including u-d initiation criterion, explosive reactive degree, explosive pressure, and particle velocity of the panels), it can be determined whether the low-density shaped jet can reliably initiate the sandwich charge. The results show that the three kinds of low-density shaped jets can not only initiate the reaction armor, but are also superior to the existing copper shaped jet in ductility, jet tip velocity, jet tip diameter, and the mass; namely, it is feasible to use the low-density material shaped jet to destroy the ERA.

21 December 2019 in Materials
Verified
Journal Article
Open access
PDF file
JZJingyuan Zhou
Jingyuan Zhou
LDLiangliang Ding
Liangliang Ding
WTWenhui Tang
Wenhui Tang
XRXianwen Ran
Xianwen Ran
Metal/fluoropolymer materials are typical reactive materials. Polytetrafluoroethylene (PTFE)/Al/CuO reactive materials were studied in this research. Scanning electron microscopy (SEM), quasi-static compression, the Split Hopkinson pressure bar test, and the drop hammer test were used to study the mechanical properties and induced reaction characteristics of the reactive materials with different Al/CuO thermite contents and different particle sizes. SEM images of the samples demonstrate that the reactive materials were mixed evenly. The compression test results show that, if the particle size of PTFE was too small, the strength of reactive materials after sintering was reduced. After sintering, with the increase in the content of Al/CuO thermite, the strength of the micro-sized PTFE/Al/CuO firstly increased and then decreased. The Johnson–Cook constitutive model can be used to characterize the reactive materials, and the parameters of the Johnson–Cook constitutive model of No. 3 reactive materials (PTFE/Al:Al/CuO = 3:1) were obtained. The reliability of the parameters was verified by numerical simulation. Drop hammer tests show that the addition of Al/CuO aluminothermic materials or the use of nano-sized PTFE/Al reactive materials can significantly improve the sensitivity of the material. The research in this paper can provide a reference for the preparation, transportation, storage, and application of reactive materials.

28 November 2019 in Materials
Verified
Journal Article
Open access
PDF file
XRXianwen Ran
Xianwen Ran
LDLiangliang Ding
Liangliang Ding
JZJingyuan Zhou
Jingyuan Zhou
WTWenhui Tang
Wenhui Tang
Currently, PTFE/Al is widely used in the reactive fragmentation warhead. However, for the same explosive yield, the reactive fragments usually have a smaller damage-radius than the inert fragments because PTFE/Al has a poor penetration ability and needs an impact-speed up to 1000 m/s to stimulate its chemical reaction. To enhance the damage power of reactive fragments, six kinds of reactive materials (PTFE/Al, PTFE/B, PTFE/Si, PTFE/Al/B, PTFE/Al/Si, and PTFE/Al/CuO) based on PTFE were designed and studied. Through the drop weight system and the self-designed energy release test device, qualitative and quantitative analysis of the energy release ability of six kinds of reactive materials were carried out. The qualitative analysis results indicate that the reactions of PTFE/B and PTFE/Si are weak under the impact of drop hammer with only a very weak fire light produced, while the reactions of PTFE/Al, PTFE/Al/B, PTFE/Al/Si, and PTFE/Al/CuO are relatively intense, and the reaction of PTFE/Al/Si is the most intense. Through the self-designed energy release test device, the energy release ability of the reactive material was quantitatively compared and analyzed. The results show that the energy release ability of the four formulations were as follows: PTFE/Al/Si > PTFE/Al/CuO > PTFE/Al/B > PTFE/Al. Therefore, it can be concluded that the PTFE/Al/Si formulation is a new reactive material with strong energy release ability, which can be a new choice for reactive fragment.

25 January 2023 in Polymers
Verified
Journal Article
Open access
PDF file
JZJingyuan Zhou
Jingyuan Zhou
XRXianwen Ran
Xianwen Ran
WTWenhui Tang
Wenhui Tang
KZKun Zhang
Kun Zhang
HWHaifu Wang
Haifu Wang
LDLiangliang Ding
Liangliang Ding
With the improvement of protection technology, the damage power of conventional penetrators has become increasingly inferior. Reactive material is a new type of energetic material, which has strong energy release capabilities under high-velocity-impact conditions. In this paper, the reactive materials were put into the penetrator, and its penetration characteristics were studied. First, the penetrator with enhanced lateral effect (PELE) projectile structure with better penetration capability was obtained by numerical simulation. Then, based on the established polytetrafluoroethylene (PTFE)/Al reactive material reaction model, the numerical simulation and experimental research of the PELE projectile with a reactive inner core penetrating the target were carried out. The results show that the simulation results are in good agreement with the experimental results, which verifies the confidence of the numerical simulation. The PELE projectile had a significant increase in power with the use of a truncated conical head and reactive materials. The residual velocity of the truncated cone PELE projectile increases by 8.41–21% over conventional PELE projectiles. Its damage range is 43% higher than that of conventional penetrators. The simulation method and the conclusions obtained in this paper can provide support and reference for further research on reactive materials and on effectively improving the damage power of the penetrator.

1 January 2017 in Shock and Vibration
Verified
Journal Article
Open access
PDF file
LDLiangliang Ding
Liangliang Ding
ZLZhenduo Li
Zhenduo Li
MLMinzu Liang
Minzu Liang
XLXiangyu Li
Xiangyu Li
FLFangyun Lu
Fangyun Lu
In order to obtain the dispersion rule of fragments about the asymmetric shell subjected to internal blast loading, two different cross section structures, concave-shaped and convex-shaped, were carried out by experimental and numerical methods. The simulation results well coincided with the experimental results, and the spatial distribution and fragment velocity were obtained. The optimal curvatures for the different concave structures changed from 4r to 6r (r represents the charge radius), as the central angle of concave structure changed from 90° to 120°. However, the optimal curvature changed weakly when the central angle of concave structure was larger than 120°. In addition, a formula which can rapidly predict the projection angle range was fitted for the convex structure. The conclusions can provide a reference for concave-shaped and convex-shaped structures to achieve a higher effectiveness of fragments.