Metal/polymer reactive materials have been studied and applied in a wide range of ways in recent years. This type of material is insensitive under normal conditions but reacts violently and releases a large amount of chemical energy under high-speed impact or high strain rate loading conditions. Compared with conventional explosives, it has better mechanical properties, and its unit mass energy is several times that of TNT. In this paper, PTFE/Al/CuO reactive materials are the main research objects, and we assess the impact energy release abilities of this type of reactive material through experimental research. To this end, eight sets of material formulations are designed, and the effects of particle size, the ratio of PTFE/Al and Al/CuO materials, and sintering on the energy release ability of the reactive materials are investigated. All experiments are carried out based on a self-designed new energy release testing device. The experimental device can measure the pressure time history curve generated by the reactive materials, and the rationality of the pressure time history curve can also be verified by the displacement time curve of the piston. The results show that with an increase in the Al/CuO thermite content, the energy release rate of the reactive material clearly increases, which is attributed to the reaction threshold of Al/CuO being low and because the heat generated can promote the reaction of PTFE/Al. The energy release rate of the nano-scale reactive materials is higher than that of the micron-scale reactive materials because the reduction in particle size results in a larger specific surface area. Thus, the energy required for ignition is lower. The energy release rate of sintered reactive materials is higher than that of unsintered reactive materials, which can be explained by the interfacial area between Al particles and PTFE particles in sintered reactive materials being larger, which makes the reaction more sufficient. The self-designed energy release testing device for the reactive materials and the conclusions obtained in this paper have clear significance for guiding engineering applications.
Metal/fluoropolymer materials are typical reactive materials. Polytetrafluoroethylene (PTFE)/Al/CuO reactive materials were studied in this research. Scanning electron microscopy (SEM), quasi-static compression, the Split Hopkinson pressure bar test, and the drop hammer test were used to study the mechanical properties and induced reaction characteristics of the reactive materials with different Al/CuO thermite contents and different particle sizes. SEM images of the samples demonstrate that the reactive materials were mixed evenly. The compression test results show that, if the particle size of PTFE was too small, the strength of reactive materials after sintering was reduced. After sintering, with the increase in the content of Al/CuO thermite, the strength of the micro-sized PTFE/Al/CuO firstly increased and then decreased. The Johnson–Cook constitutive model can be used to characterize the reactive materials, and the parameters of the Johnson–Cook constitutive model of No. 3 reactive materials (PTFE/Al:Al/CuO = 3:1) were obtained. The reliability of the parameters was verified by numerical simulation. Drop hammer tests show that the addition of Al/CuO aluminothermic materials or the use of nano-sized PTFE/Al reactive materials can significantly improve the sensitivity of the material. The research in this paper can provide a reference for the preparation, transportation, storage, and application of reactive materials.
Currently, PTFE/Al is widely used in the reactive fragmentation warhead. However, for the same explosive yield, the reactive fragments usually have a smaller damage-radius than the inert fragments because PTFE/Al has a poor penetration ability and needs an impact-speed up to 1000 m/s to stimulate its chemical reaction. To enhance the damage power of reactive fragments, six kinds of reactive materials (PTFE/Al, PTFE/B, PTFE/Si, PTFE/Al/B, PTFE/Al/Si, and PTFE/Al/CuO) based on PTFE were designed and studied. Through the drop weight system and the self-designed energy release test device, qualitative and quantitative analysis of the energy release ability of six kinds of reactive materials were carried out. The qualitative analysis results indicate that the reactions of PTFE/B and PTFE/Si are weak under the impact of drop hammer with only a very weak fire light produced, while the reactions of PTFE/Al, PTFE/Al/B, PTFE/Al/Si, and PTFE/Al/CuO are relatively intense, and the reaction of PTFE/Al/Si is the most intense. Through the self-designed energy release test device, the energy release ability of the reactive material was quantitatively compared and analyzed. The results show that the energy release ability of the four formulations were as follows: PTFE/Al/Si > PTFE/Al/CuO > PTFE/Al/B > PTFE/Al. Therefore, it can be concluded that the PTFE/Al/Si formulation is a new reactive material with strong energy release ability, which can be a new choice for reactive fragment.
In order to more realistically reflect the penetrating and crushing process of a PELE (Penetration with Enhanced Lateral Efficiency) projectile, the stochastic failure algorithm and crack-softening algorithm were added to the corresponding material in this paper. According to the theoretical analysis of the two algorithms, the material failure parameters (stochastic constant γ, fracture energy Gf, and tensile strength σT) were determined. Then, four sets of simulation conditions ((a) no crack softening, (b) no stochastic failure, (c) no crack softening and no stochastic failure, and (d) crack softening and stochastic failure) were designed to qualitatively describe the influences of the failure algorithms, which were simulated by the finite element analysis software AUTODYN. The qualitative comparison results indicate that the simulation results after adding the two algorithms were closer to the actual situation. Finally, ten groups of simulation conditions were designed to quantitatively analyze the coincidence degree between the simulation results and the experimental results by means of two parameters: the residual velocity of the projectile and the maximum radial velocity of fragments. The results show that the simulation results coincide well with the experimental results and the errors were small. Therefore, the ideas proposed in this paper are scientific, and the conclusions obtained can provide guidance for engineering research.
With the improvement of protection technology, the damage power of conventional penetrators has become increasingly inferior. Reactive material is a new type of energetic material, which has strong energy release capabilities under high-velocity-impact conditions. In this paper, the reactive materials were put into the penetrator, and its penetration characteristics were studied. First, the penetrator with enhanced lateral effect (PELE) projectile structure with better penetration capability was obtained by numerical simulation. Then, based on the established polytetrafluoroethylene (PTFE)/Al reactive material reaction model, the numerical simulation and experimental research of the PELE projectile with a reactive inner core penetrating the target were carried out. The results show that the simulation results are in good agreement with the experimental results, which verifies the confidence of the numerical simulation. The PELE projectile had a significant increase in power with the use of a truncated conical head and reactive materials. The residual velocity of the truncated cone PELE projectile increases by 8.41–21% over conventional PELE projectiles. Its damage range is 43% higher than that of conventional penetrators. The simulation method and the conclusions obtained in this paper can provide support and reference for further research on reactive materials and on effectively improving the damage power of the penetrator.
PELE projectile is a new type of armor-piercing warhead and has a more obvious fragmentation effect, which solves the problem of insufficient after-effects of conventional armor-piercing projectiles. Reactive material is a new type of energetic material, which has some characteristics similar to the traditional explosives but has better mechanical properties. Reactive material is insensitive under normal conditions, and it can release huge energy under external impact loading. This paper hopes to study the application of reactive materials to the inner core of PELE projectiles to further improve the fragmentation effect of PELE projectiles. The fragmentation effect of PELE projectile is mainly reflected in the radial scattering velocity of fragments after it perforates the target plate. In this paper, three energy sources for the radial scattering of fragments were obtained by analyzing the penetration process of PELE projectile, that is, the axial kinetic energy of outer casing, the radial compression potential energy generated by the inner core to the outer casing, and the chemical energy released by the reactive core material. Based on the simplification and assumptions, the theoretical model of radial scattering velocity of fragments of the reactive core PELE projectile was established. In addition, numerical simulations were carried out to verify the theoretical model. The results show that the numerical simulation results are in good agreement with the theoretical calculation results, which indicates that the model established in this paper is scientific and reasonable. The reactive core PELE projectile has a more significant fragmentation effect, which further enhances the comprehensive damage power of traditional PELE projectile. The theoretical model established in this paper can quickly assess the power of reactive core PELE projectile’s fragmentation effect, which can be used to provide guidance and reference for engineering application.