The transport of Zn(II) ions across polymer inclusion membranes (PIMs) with acetylacetone (ACAC) or di(2-ethylhexyl)phosphoric acid (D2EHPA) as carriers was studied. Polymeric membranes consisting of polyvinylchloride (PVC) as the support, bis(2-ethylhexyl)adipate (DAO) as plasticizer, and ACAC or D2EHPA as ion carriers were investigated. The highest recovery factors for Zn(II) ions were observed in the case of a membrane containing 20% acac (99.6%) and 60% D2EHPA (56.3%). The prepared PIMs were examined using atomic force microscopy (AFM) techniques. Their mechanical properties were also determined. The influence of membrane morphology and mechanical properties on the zinc transport process was discussed.
The selective transport of various metal ions through a novel polymer inclusion membrane (PIM) doped with β-diketone derivatives (acetylacetone (1), 3-propyl-acetylacetone (2), and 3-benzyl-acetylacetone (3)) was investigated. Initial fluxes of metal ions transport across PIMs decrease in the following sequence: Zn(II) > Cu(II) > Co(II) > Ni(II). Results show that zinc(II) can be effectively separated by studied PIMs from equimolar aqueous solutions of copper, zinc, cobalt, and nickel nitrates. At pH 7.5 and after 24 hours 87–93% of Zn(II) was recovered. It was found that membranes containing 2 and 3 separate zinc better than PIM with 1. Prepared PIMs were characterized using AFM and thermal analysis techniques.
Polymer inclusion membranes (PIMs) doped with ethylenodiamino-bis-acetylacetone as fixed carrier was applied for the investigation of the facilitated transport of Zn(II), Cr(III), and Ni(II) ions from an aqueous nitrate feed phase (cM = 0.001 mol/dm3). The optimal membrane composition (amount of carrier and o-NPPE-plasticizer) was determined. For the optimal polymer inclusion membranes doped with ethylenodiamino-bis-acetylacetone, the following patterns of transport selectivity were found: Zn(II) > Cr(III) > Ni(II). The initial flux of Zn(II), Cr(III), and Ni(II) ions was 6.37 µmol/m2∙s, 5.53 µmol/m2∙s, and 0.40 µmol/m2∙s, respectively. The selectivity coefficients equal to 1.2 and 15.9 were found for Zn(II)/Cr(III) and Zn(II)/Ni(II), respectively. After 24-h transport, the recovery factor of Zn(II), Cr(III), and Ni(II) were 90%, 65%, and 6%, respectively. The polymer inclusion membranes doped with ethylenodiamino-bis-acetylacetone were characterized by scanning electron microscopy and non-contact atomic force microscopy. The influence of membrane morphology on transport process was discussed.
Polymer cellulose triacetate membranes doped with 1-alkylimidazole as fixed carriers were applied for the investigation of the facilitated transport of Zn(II) and Mn(II) ions from an aqueous sulphate feed phase (cM = 0.001 mol/dm3). For the polymer inclusion membranes (PIMs) doped with 1-alkylimidazole (alkyl – from hexyl up to decyl), the following patterns of transport selectivity were found: Zn(II) > Mn(II). The highest initial flux of Zn(II) ions (2.65 µmol/m2·s) was found for PIMs doped with 1-decyl-imidazole, whereas the best Zn(II)/Mn(II) selectivity coefficients equal to 19.7 were found for 1-hexyl-imidazole. Permeability coefficients for Zn(II) and Mn(II) ions transported across PIMs increase with an increase in the pKa values of 1-alkylimidazole. The polymer membranes of cellulose triacetate-o-NPPE with 1-alkylimidazole were characterised by scanning electron microscopy, non-contact atomic force microscopy and thermal analysis techniques. The influence of membrane morphology on the Zn(II) and Mn(II) transport process was discussed.
28 March 2012 in Separation Science and Technology
The selective transport of copper(II), zinc(II), cobalt(II), and nickel(II) ions from nitrate solutions across polymer inclusion membranes (PIMs), which consist of cellulose triacetate as polymeric support, o-nitrophenyl pentyl ether as plasticizer, and 1-alkylimidazole (alkyl from hexyl- to decyl) as ion carrier was reported. PIM was characterized by using atomic force microscopy (AFM) technique. The results show that Cu(II) can be separated very effectively from other transition metal cations as Zn(II), Co(II), and Ni(II) (at a concentration of 10−3 mol/dm3 each). Alkyl substituents at position 1 of the imidazole ring have been found to affect the hydrophobic properties and initial flux of the transported metal ions. The efficiency of separation of metal ions by 1-alkylimidazole followed the sequence: Cu(II) > Zn(II) > Co(II) > Ni(II). The highest selectivity coefficient for Cu(II) was found with 1-hexylimidazole and its 1 mol/dm3 solution in PIM. Separation of the ions was more effective for the nitrates(V) than for chlorides.
4 November 2019 in Journal of Thermal Analysis and Calorimetry
Membrane techniques can be used to separate different compounds, i.e., toxic metal ions from waste waters. As any other method of separation, also this one, based on polymer inclusion membranes (PIMs), has certain limitations. One of them is the stability of membranes. In the present paper, the dependence of the physical and chemical properties on composition of PVC-based polymer inclusion membranes doped with phosphonium ionic liquids (CYPHOS IL 101, CYPHOS IL 104, CYPHOS IL 105 and CYPHOS IL 109) was studied. The thermal stability of investigated membranes was examined by thermogravimetry together with differential thermogravimetry analysis. Obtained results showed that studied PIMs are stable to the temperature of about 170 °C. The membrane morphology was examined by attenuated total reflectance Fourier-transform infrared (ATR-FTIR) spectroscopy, as well as scanning electron microscopy (SEM). The visibility of all characteristic bands in the ATR-FTIR spectra confirmed the presence of individual components in the membranes: a polymer, a plasticizer and the carriers. It also suggested that there were no signs of the covalent bond formation between the polymer, the plasticizer and the carrier. Only van der Waals or hydrogen bonds could be present. Moreover, in the SEM images of the investigated PIMs a rough surface without pores was observed.