Limestone pore structure strongly influences dissolution and associated reactive transport. These effects are critical in limestone diagenesis and but also in engineering operations such as carbon capture and storage (CCS). However, detailed studies on how CO2‐enriched (acidic) brine changes this pore structure at relevant reservoir storage conditions are very limited. Thus, to provide further quantitative information and more fundamental understanding about these key processes, we studied the dissolution patterns of a homogeneous, a fractured, and a vuggy limestone when flooded with CO2‐saturated brine at representative storage conditions. The pore structured of these limestones showed drastically different responses to the acidic brine flood. As such, preferential channels surrounded by branched channels were formed in the homogeneous sample, while fractures became the main flow path in the fractured sample. In contrast, only one dominant channel formed in the vuggy sample, which resulted in a sharp permeability increase. These dissolution patterns reflect the associated Damköhler number, which significantly lower in the homogeneous, representing uniform dissolution. However, after injecting sufficient reactive fluid (1,000 PV), this uniform dissolution pattern transformed into a single preferential channel growth. Moreover, we conclude that increasing complexity of the pore geometry leads to more nonuniform dissolution. These dissolution patterns indicate the effect of initial pore structure on preferential channel growth and reaction transport. Our work provides key fundamental data for further quantifying limestone dissolution patterns in CCS, indicating that the CO2 injection may cause the reactivation of geological faults and damage around wellbore, thus aids in the implementation of industrial‐scale CCS.
Fluid flow in nanoscale organic pores is known to be affected by fluid transport mechanisms and properties within confined pore space. The flow of gas and water shows notably different characteristics compared with conventional continuum modeling approach. A pore network flow model is developed and implemented in this work. A 3‐D organic pore network model is constructed from 3‐D image that is reconstructed from 2‐D shale SEM image of organic‐rich sample. The 3‐D pore network model is assumed to be gas‐wet and to contain initially gas‐filled pores only, and the flow model is concerned with drainage process. Gas flow considers a full range of gas transport mechanisms, including viscous flow, Knudsen diffusion, surface diffusion, ad/desorption, and gas PVT and viscosity using a modified van der Waals' EoS and a correlation for natural gas, respectively. The influences of slip length, contact angle, and gas adsorption layer on water flow are considered. Surface tension considers the pore size and temperature effects. Invasion percolation is applied to calculate gas‐water relative permeability. The results indicate that the influences of pore pressure and temperature on water phase relative permeabilities are negligible while gas phase relative permeabilities are relatively larger in higher temperatures and lower pore pressures. Gas phase relative permeability increases while water phase relative permeability decreases with the shrinkage of pore size. This can be attributed to the fact that gas adsorption layer decreases the effective flow area of the water phase and surface diffusion capacity for adsorbed gas is enhanced in small pore size.
Water flooding is an economic method commonly used in secondary recovery, but a large quantity of crude oil is still trapped in reservoirs after water flooding. A deep understanding of the distribution of residual oil is essential for the subsequent development of water flooding. In this study, a pore-scale model is developed to study the formation process and distribution characteristics of residual oil. The Navier–Stokes equation coupled with a phase field method is employed to describe the flooding process and track the interface of fluids. The results show a significant difference in residual oil distribution at different wetting conditions. The difference is also reflected in the oil recovery and water cut curves. Much more oil is displaced in water-wet porous media than oil-wet porous media after water breakthrough. Furthermore, enhanced oil recovery (EOR) mechanisms of both surfactant and polymer flooding are studied, and the effect of operation times for different EOR methods are analyzed. The surfactant flooding not only improves oil displacement efficiency, but also increases microscale sweep efficiency by reducing the entry pressure of micropores. Polymer weakens the effect of capillary force by increasing the viscous force, which leads to an improvement in sweep efficiency. The injection time of the surfactant has an important impact on the field development due to the formation of predominant pathway, but the EOR effect of polymer flooding does not have a similar correlation with the operation times. Results from this study can provide theoretical guidance for the appropriate design of EOR methods such as the application of surfactant and polymer flooding.