Wenxue Zhang

Dr. Wenxue Zhang


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2016 in Construction and Building Materials
Verified
Journal Article
Closed access
WZWenxue Zhang
Wenxue Zhang
JHJian Huang
Jian Huang
ZLZengyin Li
Zengyin Li
CHChun Huang
Chun Huang

27 September 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
HCHuating Chen
Huating Chen
ZSZhenyu Sun
Zhenyu Sun
XZXianwei Zhang
Xianwei Zhang
WZWenxue Zhang
Wenxue Zhang
Concrete structures such as bridge decks and road pavements are subjected to repetitive loading and are susceptible to fatigue failure. A simplified stress–strain analysis method that can simulate concrete behavior with a sound physical basis, acceptable prediction precision, and reasonable computation cost is urgently needed to address the critical issue of high-cycle fatigue in structural engineering. An equivalent fatigue constitutive model at discrete loading cycles incorporated into the concrete damaged plasticity model (CDPM) in Abaqus is proposed based on fatigue damage evolution. A damage variable is constructed from maximum fatigue strains, and fatigue damage evolution is described by a general equation whose parameters’ physical meaning and value range are identified. With the descending branch of the monotonic stress–strain curve as the envelope of fatigue residual strength and fatigue damage evolution equation as shape function, fatigue residual strength, residual stiffness, and residual strain are calculated. The equivalent fatigue constitutive model is validated through comparison with experimental data, where satisfactory simulation results were obtained for axial compression and flexural tension fatigue. The model’s novelty lies in integrating the fatigue damage evolution equation with CDPM, explicitly explaining performance degradation caused by fatigue damage. The proposed model could accommodate various forms of concrete constitution and fatigue stress states and has a broad application prospect for fatigue analysis of concrete structures.

1 October 2017 in Journal of Bridge Engineering
Verified
Journal Article
Closed access
WZWenxue Zhang
Wenxue Zhang
RFRong Fang
Rong Fang
SCShitong Chen
Shitong Chen
HZHanqing Zhao
Hanqing Zhao
Current sliding-bearing designs do not make full use of the stiffness and potential ability of sliding piers in the aseismic design of continuous bridges. Aiming at the problem that the demand on the only fixed-pier force and beam-end longitudinal displacement is too large under longitudinal direction earthquakes, an aseismic design idea of a continuous bridge is proposed based on coloading of all piers by installing locking balls between the sliding piers and the continuous girder. This device can also handle displacement caused by rise and drop in temperature. When a strong earthquake occurs, the locking ball is activated, and the locking connections between the girder and the sliding piers were built to let the sliding piers carry the longitudinal seismic load of the superstructure in conjunction with the fixed pier. A vibration-table experiment on a three-span continuous bridge with a scale of 1:25 was conducted, and results were compared with finite-element model (FEM) simulations. The aseismic effect and the mechanism of the locking ball on the continuous bridge were analyzed. The results showed that the sliding piers can bear the longitudinal seismic load of the upper structure in conjunction with the fixed pier under strong earthquake conditions and can improve the overall aseismic performance of the continuous bridge significantly. Meanwhile, the seismic demands on the sliding piers increased. The number of spans and the length of the continuous girder had an influence on the locking-ball aseismic effect. However, the variation of temperature had little influence on the aseismic effect of the locking ball.

16 February 2024 in Journal of Building Engineering
Verified
Journal Article
Closed access
CZCheng Zhang
Cheng Zhang
WZWenxue Zhang
Wenxue Zhang
WLWen Li
Wen Li
JWJunwei Wang
Junwei Wang
XDXiuli Du
Xiuli Du

13 October 2017 in Archive of Applied Mechanics
Verified
Journal Article
Closed access
PDF file
WZWenxue Zhang
Wenxue Zhang
YCYing Chen
Ying Chen
WKWenqi Kou
Wenqi Kou
XDXiuli Du
Xiuli Du

18 March 2022 in Sustainability
Verified
Journal Article
Open access
PDF file
YZYongRui Zheng
YongRui Zheng
JWJin Wang
Jin Wang
WXWeibing Xu
Weibing Xu
NLNana Li
Nana Li
WZWenxue Zhang
Wenxue Zhang
YCYanjiang Chen
Yanjiang Chen
Curved high-pier rigid frame bridges (CHRF bridges) are unavoidably affected by near-fault ground motions (NFGMs), and seismic pounding between adjacent components of CHRF bridge has a significant effect on the seismic performance of CHRF bridges. The seismic response and seismic pounding laws of CHRF bridges under NFGMs need further investigation. In this study, the influence of NFGMs with impulse and directional effects on the dynamic response of CHRF bridges was studied. Subsequently, the pounding responses between adjacent components of CHRF bridge were systematically analyzed. The results showed that the impulse and directional effects of NFGMs have a significant impact on the seismic response of CHRF bridges. The seismic response of CHRF bridges under near-fault impulse-like ground motions (IPGMs) is greater than that under near-fault non-pulse-like ground motions (NPGMs). CHRF bridges have the lowest seismic response under far-fault ground motions (FFGMs). The seismic response of CHRF bridges is significant under backward region ground motions (BRGMs) and the lowest under forward region ground motions (FRGMs). The IPGMs induce larger pounding force (PF) and a smaller number of poundings (PN) compared with FFGMs. The PF and the PN increase from the FRGMs to the BRGMs. Because of the pounding, the impulse and directional effects of NFGMs cause the shear force of the main pier and the auxiliary pier of CHRF bridges to increase significantly and the relative bending moment decreases. Moreover, the shear force and bending moment of the tie beam increases significantly owing to pounding.