The demodulation algorithm based on 3 × 3 coupler in a fiber-optic hydrophone array has gained extensive attention in recent years. The traditional method uses a circulator to construct the normal path-match interferometry; however, the problem of increasing the asymmetry of the three-way signal to be demodulated is easily overlooked. To provide a solution, we report a pretreatment method for hydrophone array based on 3 × 3 coupler demodulation. We use cubic spline interpolation to perform nonlinear fitting to the reflected pulse train and calculate the peak-to-peak values of the single pulse to determine the light intensity compensation coefficient of the interference signal, so as to demodulate the corrected three-way interference signal. For experimental verification, ultra-weak fiber Bragg gratings (uwFBGs) with reflectivity of −50 dB are applied to construct a hydrophone array with 800 sensors, and a vibratory liquid column method is set up to generate a low-frequency hydroacoustic signal. Compared to the traditional demodulation algorithm based on a 3 × 3 coupler, the pretreatment method can improve the consistency of interference signals. The Lissajous figures show that cubic spline interpolation can improve the accuracy of monopulse peak seeking results by about 1 dB, and intensity compensation can further lead to a much lower noise density level for the interference pulse amplitude—specifically, more than 7 dB at 5~50 Hz—and the signal-to-noise ratio is improved by approximately 10 dB at 10 Hz. The distinct advantages of the proposed pretreatment method make it an excellent candidate for a hydrophone array system based on path-match interferometry.

This paper investigates a 1.7 mm diameter ultra-weak fiber Bragg grating (UWFBG) hydrophone towed array cable for acoustic direction finding. The mechanism of the underwater acoustic waves received by this integrated-coating sensitizing optical cable is deduced, and it is shown that the amplitude of its response varies with the direction of the sound wave. An anechoic pool experiment is carried out to test the performance of such a hydrophone array. The test array is a selection of six sensing fibers, each of which is coiled into 9 cm diameter fiber ring suspended in the water to receive acoustic signals. An average sensitivity of −141.2 dB re rad/μPa at frequencies from 2.5 kHz to 6.3 kHz was achieved, validating the detection of the azimuth of underwater acoustic waves. The ultra-thin towing cable system, with free structure, high sensitivity, and underwater target-detection capability has demonstrated great potential for future unmanned underwater vehicle (UUV) applications.

To address the demand of equivalent self-noise suppression in a distributed hydroacoustic sensing system, this study proposes a method to enhance the acoustic sensitivity and signal-to-noise ratio (SNR) using space division multiplexed (SDM) technology based on multi-core fiber (MCF). Specifically, a dual-channel demodulation system for distributed acoustic sensing is designed using MCF. The responses of different cores in MCF are almost consistent under external acoustic pressure, while their self-noise is inconsistent. Accordingly, the acoustic pressure phase sensitivity (APPS) and SNR gain based on the accumulation of dual-channel signals are analyzed, which are verified by experiments. It is shown that the self-noise correlation coefficient between the two cores is 0.11, increasing the noise power by 3.46 dB. The APPS is increased by 5.97 dB re 1 rad/μPa after the accumulation of two-core signals, which is close to the theoretical value (6 dB). The equivalent self-noise is reduced by 2.54 dB. The experimental results reveal that the enhancement of acoustic pressure phase shift sensitivity and SNR can be achieved by the space division multiplexing (SDM) of multi-core signals, which is of great significance for suppressing the equivalent self-noise of the system and realizing the acoustic pressure detection of weak underwater signals.

The pump heating effect of DFB fiber laser is normally ignored due to the short length of the laser cavity. However, by fabricating a phase-shifted FBG on high concentration Er-Yb codoped fiber to obtain a 16 mm long DFB fiber laser, the gradient surface temperature distributions along the active grating with different pump powers were observed. The average surface temperature rose by 16.82 K with a variation of less than 1.11 K, and the position with the highest temperature moved towards the center of the grating by 5.5 mm, when the pump power was increased from 0 mW to 191.6 mW. The transmission spectrum of the active phase-shifted FBG at different pump powers were measured, and an additional drift of the transmission peak in the stopband was testified. It was identified as an equivalent phase shift up to −0.1 π, which was induced by the gradient longitudinal temperature distribution. Considering that the initial phase shift of the grating was about 1.15 π, the increasing chirp of the active grating due to the pump heating could compensate the phase shift deviation from π surprisingly. The experimental results coincided with the simulation results by using the transmission matrix method under the assumption of piecewise-uniform structure for the chirped phase-shifted grating. The modified model of the active phase-shifted FBG reveals the difference between the cool cavity and the hot cavity at different pump powers, which may be used as a self-optimization mechanism for DFB fiber laser operation.

Multi-core fiber (MCF) has drawn increasing attention for its potential application in distributed acoustic sensing (DAS) due to the compact optical structure of integrating several fiber cores in the same cladding, which indicates an intrinsic space-division-multiplexed (SDM) capability in a single piece of fiber. In this paper, a dual-channel DAS integrated with MCF is presented, of which the equivalent self-noise characteristic is analyzed. The equivalent self-noise of the system can be effectively suppressed by signal superposition with the phase matching method. Considering that the noise correlation among the cores is not zero, the signal-to-noise (SNR) gain after signal superposition is less than the theoretical value. The dual-channel DAS system is set up by a piece of 2 km long seven-core MCF, in which the dual-sensing channels are constructed by a four-core series and three-core series, respectively. The total noise correlation coefficient of the seven cores is 11.28, while the equivalent self-noise of the system can be suppressed by 6.32 dB with signal superposition. An equivalent self-noise suppression method based on a linear delay phase matching scheme is proposed for noise decorrelation in the DAS MCF system. After noise decorrelation, the suppression of the equivalent self-noise of the system can reach the theoretical value of 8.45 dB with a time delay of 1 ms, indicating a noise correlation among the seven cores of almost zero. The feasibility of the equivalent self-noise suppression method for the DAS system is verified for both single-frequency and broadband signals, which is of great significance for the detection of weak vibration signals based on a DAS system.

In this paper, we propose a method for detecting the center wavelength of ultra-weak chirped fiber Bragg grating (uwCFBG) with a jittery spectrum, based on the solution of the correlation coefficient. We establish a mathematical model for uwCFBG by superimposing segmented step Gaussian functions with noise. Then, we analyze the variation trajectory of the correlation coefficient under different relative positions through simulation. Finally, we conduct a comparative analysis of the 284-element uwCFBGs. The experimental results show that the extreme difference of the center wavelength calculation is 0.19 nm and the variance is 0.08, which proves that the proposed algorithm process is simpler and the results are more robust.