KARTHIK S

Mr. KARTHIK S

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 March 2024 in International Journal of Electrochemical Science
Verified
Journal Article
Open access
KSKARTHIK S
KARTHIK S
KPKarunakaran P
Karunakaran P
VGVelmurugan G
Velmurugan G

1 January 2025 in Materials Research Express
Verified
Journal Article
Open access
KSKARTHIK S
KARTHIK S
SASivakumar Annamalai
Sivakumar Annamalai
Titanium Diboride is a highly used material in aerospace industry due of its remarkable longevity. Its strength poses a problem to traditional machining methods. This work aims to compare two different dielectric fluids and four different electrode materials to improve EDM process parameters in TiB2 material. The input parameters were adjusted to find the optimal combination. By studying the fluctuations of output parameters such as MRR, TWR, SR and overcut when processing titanium diboride, researchers can gain valuable insights. This is achieved through experimental studies and the results are then verified using a theoretical regression model. Experimental results confirmed that discharge current, voltage and Ton had a remarkable influence on MRR, TWR and surface roughness in TiB2 material. It has been observed that tool wear rate when using kerosene-based dielectric fluids is higher than that of deionized water-based dielectric fluids. Tungsten copper electrodes cause slightly less tool wear than tungsten electrodes, and produce higher MRR overall, when compared to other three electrode materials. Using deionized water as a dielectric fluid and a copper as an electrode material can help to obtain a smoother surface. When deionized water is used as a dielectric fluid with tungsten electrodes, the overcut value drops dramatically. Brass electrodes produce a higher overcut value compared to the other three electrode materials. The microstructure of the EDM hole was distinguished by SEM analysis, and the material composition of TIB2 was determined by EDS analysis.

22 June 2026 in Archives of Metallurgy and Materials
Verified
Journal Article
Open access
PDF file
SNSreenivasaraja Nagarajan
Sreenivasaraja Nagarajan
KMKathiresan Marimuthu
Kathiresan Marimuthu
KSKARTHIK S
KARTHIK S
VGVelmurugan G
Velmurugan G
In this study the mechanical, wear, and electrical discharge machining (EDM) performance of biodegradable WE43 magnesium alloy was enhanced by adding ceramic reinforcement like silicon carbide, aluminium oxide, and boron carbide. Two hybrid composite specimens were fabricated in this investigation with WE43 MMC 1 is reinforced with 6 wt.% reinforcement (2% SiC, 2% Al2O3, and 2% B₄C) and WE43 MMC 2 with 10 wt.% reinforcement (3.5% SiC, 3.5% Al2O3, and 3% B4C). The weight % of ceramic reinforcement content is increased, the yield strength is enhanced from 158.69 MPa to 211.47 MPa, ultimate tensile strength is improved from 241.25 MPa to 285.36 MPa, and hardness from 65.8 to 89.4. However, there was a drop-in ductility, with elongation falling from 6.52% to 3.25%, showing that there is a trade-off between strength and plasticity. The hard-ceramic content made the material more resistant to wear and are expected to make EDM easier by reducing electrode wear and improving surface quality because they are more thermally stable. SEM and EDS analysis are carried out in this study to evaluate the microstructural and surface topography of WE43 MMC. The result of this study demonstrates that the WE43 MMC 2 are promising candidates for high-performance applications in biomedical and aerospace sectors requiring lightweight materials with superior mechanical and EDM-compatible properties.

1 January 2025 in High Temperature Materials and Processes
Verified
Journal Article
Open access
PDF file
KSKARTHIK S
KARTHIK S
SASivakumar Annamalai
Sivakumar Annamalai
NTNathiya Thangaraj
Nathiya Thangaraj
The aerospace industry widely uses titanium diboride, a tough material that is challenging to machine using conventional methods. We, therefore, process titanium diboride (TiB₂) to determine the best process parameters for electrical discharge machining for TiB₂. The study compares four electrode materials: brass, copper, tungsten, and tungsten copper. In addition, water-based deionized (DI) dielectric fluids are studied, and the input parameters are changed to measure the fluctuations of the output parameters through experimental studies and gain insights into the material removal rate (MRR), tool wear rate (TWR), surface roughness (SR), and overcut during machining of titanium diboride. We then verify this result using gray relational analysis and a regression model. Based on these results, we confirm that the discharge current is the most important factor affecting the MRR and SR. The copper electrode achieves a higher MRR, while the tungsten copper-based electrode leads to a lesser TWR. A copper electrode achieves better SR, while tungsten electrodes with DI water-based dielectric fluid show a lower overcut value. After machining, we used SEM to check the surface quality and elemental makeup and to see if there were any microstructural changes, like craters, recast layers, and maybe even microcracks, that were caused by the high-energy discharge process.

18 December 2025 in Materials Research Express
Verified
Journal Article
Open access
VGVelmurugan G
Velmurugan G
KMKathiresan M
Kathiresan M
SMSanjay Muralidharan
Sanjay Muralidharan
KSKARTHIK S
KARTHIK S
The superior mechanical and physical properties of aluminum metal matrix composites over the underlying Al alloy make them popular in a wide range of applications. The LM6, LM25, and LM4 alloys are reinforced with ceramic particles made of silicon carbide (SiC) 2% to 4%, magnesium nitride (Mg₃N₂) 2% to 4%, and gallium nitride (GaN) 0.5% to 1%, despite their extreme strength and durability. The die casting process was used to create a hybrid aluminum metal matrix composite. The mechanical behavior of the created metal matrix composite (MMC) was assessed using wear and tensile tests. A material's bonding ability, reinforcement pullout, and microcracks were discovered by SEM image analysis; its chemical composition was determined by XRD; and its thermal stability was assessed by TGA. A highest tensile strength of 258 N/mm2 was attained with the sample (LM25-3) that had 2% silicon carbide, 4% magnesium nitride, and 1% gallium nitride reinforcement. The sample (LM25-3) exhibits a minimum wear loss of 0.0011 mg/m at 1100 rpm with a load of 5 kg. A temperature before 400°C, the thermal residual mass vary from 97.7% to 91.3%, while 54% to 32% was consistently found above 800°C in all samples.

2 December 2025 in Silicon
Verified
Journal Article
Closed access
PDF file
KSKARTHIK S
KARTHIK S
SASivakumar Annamalai
Sivakumar Annamalai
VGVelmurugan G
Velmurugan G
JSJayaraman Ss
Jayaraman Ss