Ting Chen

Dr. Ting Chen


Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 November 2024 in Coatings
Verified
Journal Article
Open access
PDF file
TCTing Chen
Ting Chen
LYLonglin Yu
Longlin Yu
BDBoyi Deng
Boyi Deng
FWFang Wang
Fang Wang
MOMingwei Ouyang
Mingwei Ouyang
WGWen Ge
Wen Ge
In order to obtain electronic contacts with good performance, Au-Cu alloy coatings with different gold contents were prepared on copper substrates by direct current electrodeposition and were tested against electrochemical corrosion and arc corrosion. The experimental results showed that the hardness of the Au-Cu alloy was in the range of 115.2 HV~171.6 HV, which meets the requirements of electronic contact materials. The polarization curve (Tafel) test and electrochemical impedance spectroscopy (EIS) test results indicated that the electrochemical corrosion resistance of Au-Cu alloy plating was much better than pure copper. With the rise of gold content in the alloy coatings, the corrosion resistance of the alloy coatings enhanced gradually. Compared with pure copper, the Au-Cu alloy coatings showed more stable contact resistance. After 1000 contacts, the resistivity of the alloy with 75% gold varied from 72 mΩ to 78 mΩ, whereas under the same conditions, the resistivity of copper changed from 14 mΩ to 78 mΩ. Anode-type material transfer occurred after 1000 contacts with a reduction in the total mass of each contact element. The mass loss of Au75Cu25 and Au86Cu14 contact elements was lower than that of pure copper. The Au-Cu alloy coatings displayed excellent arc corrosion resistance when the gold content in the alloy plating was higher than 75%.

20 October 2010 in Acta Crystallographica Section E Structure Reports Online
Verified
Journal Article
Open access
PDF file
TCTing Chen
Ting Chen
XTXiaosong Tan
Xiaosong Tan
In the title compound, C(16)H(14)Cl(2)N(2)O(4)·H(2)O, the hydrazine and water mol-ecules are both located on twofold axes. The C-N-N-C torsion angle is -72.66 (1)° and the dihedral angle between the two benzene rings is 67.33 (1)°. In the crystal, mol-ecules are linked into a layer structure by a combination of O-H⋯O, N-H⋯O and C-H⋯O hydrogen bonds. Adjacent layers are linked into a three-dimensional network by Cl⋯Cl inter-actions [3.400 (2) Å]. C-H⋯π inter-actions are also observed.


27 November 2025 in Coatings
Verified
Journal Article
Open access
PDF file
WGWen Ge
Wen Ge
JZJia Yu Zhang
Jia Yu Zhang
XRXia Ran
Xia Ran
TCTing Chen
Ting Chen
Graphene oxide (GO) is characterized by hydrophilic edges and a more hydrophobic planar/basic skeleton, which makes it has potential applications in the field of corrosion. But its hydrophobicity hinders its co-deposition behavior in the electrolyte. To improve the corrosion resistance of copper-based substrate, this article designs and successfully prepares a nickel/chromium graphene oxide (NiCr-GO) composite coating. The paper studied the influence and mechanism of GO addition on the microstructure and corrosion resistance of the coating. The results indicate that a crack network and nodular structure have formed on the surface of the coating. The coatings with different GO contents are composed of nickel, chromium single-phase, and Cr2Ni3 inter-metallic compounds, and the grain size does not significantly change. With the increase in GO, the corrosion resistance of the composite coating is enhanced, and the optimal GO addition amount is 0.750 g/L. GO chips may form physical barriers in the crystal structure defects of the coating, or passive films on the material surface. This dual mechanism is the fundamental reason for improving the corrosion resistance of NiCr-GO.