In this paper, the authors presented an analysis of the strengthening of the cumulative jet by the appropriate formation of the detonation wave front acting under the influence of high pressure on the liner. The analysis of the Polish ŁK cumulative charge was carried out using numerical methods in the ABAQUS program. Simulation studies were carried out on axial and peripheral initiations of the explosive cumulative liner. For this purpose, two types of cumulative charges were made with the same design parameters, differing only in the explosive detonation-initiation system. The impact of the elastomer insert on the focusing of the cumulative jet was verified. The influence of peripheral and axial initiation on a cumulative jet’s velocity was investigated. The authors proposed a new conical insert placed in the explosive between the pocket for the detonator and the liner, also changing the material of the cumulative liner. The smoothed-particle hydrodynamics method was used to describe the formation of a cumulative jet. The obtained results were verified experimentally, and they show that modification of the ŁK charge has a positive effect on jet amplification, with an inevitable collapse in the final stage of formation. The obtained results correlate with the literature’s data.
The paper presents the results of studies on the effects of shooting composite materials produced by pressure infiltration with the EN AW-7075 alloy as a matrix and reinforcement in the form of preforms made of α-Al2O3 particles. Composite materials were made with two reinforcement contents (i.e., 30% and 40% vol. of α-Al2O3 particles). The composites produced in the form of 12 mm thick plates were subjected to impact loads from a 7.62 × 39 FMJ M43 projectile fired from a Kalashnikov. The samples of composites with different contents of strengthening particles were subjected to detailed microscopic examination to determine the mechanism of destruction. The effect of a projectile impact on the microstructure of the material within the perforation holes was identified. There were radial cracks found around the puncture holes and brittle fragmentation of the front surfaces of the specimens. The change in the volume of the reinforcement significantly affected the inlet, puncture and outlet diameters. The observations confirmed that brittle cracking dominated the destruction mechanism and the crack propagation front ran mainly in the matrix material and along the boundaries of the α-Al2O3 particles. In turn, numerical tests were conducted to describe the physical phenomena occurring due to the erosion of a projectile hitting a composite casing. They were performed with the use of the ABAQUS program. Based on constitutive models, the material constants developed from the identification of material properties were modelled and the finite element was generated from homogenization in the form of a representative volume element (RVE). The results of microscopic investigations of the destruction mechanism and numerical investigations were combined. The conducted tests and analyses shed light on the application possibilities of aluminium composites reinforced with Al2O3 particles in the construction of add-on-armour protective structures.
The friction behavior of the formed antifriction films and their effect on the functional properties of the composite based on the powder nickel alloy EI929 with solid lubricant CaF2 at high temperatures was investigated. An antifriction film was formed on the contact surfaces during the friction process. Such a film was the result of the interaction of the contact surfaces with atmospheric oxygen at high temperatures. It contains oxides of alloying elements from materials of the frictional contact and solid lubricant calcium fluoride. The quantitative ratio of formed oxides depends on the temperature operating conditions of material. The data of thermodynamic simulation of the high-temperature interaction of the composite with oxygen coincide with the experimental data obtained by studying the fine structure of surface antifriction films. Antifriction films consist of oxide phases in combination with solid CaF2 lubricant. Anti-friction films provide high wear resistance of the self-lubricating composite in the range of temperatures 1073–1173 K due to the balance between the rate of their formation and wear. When the temperature exceeds 1200 K, the film loses its lubricating properties and acts as an abrasive substance due to the intense oxidation. Abrasive surfaces of materials were subjected also to microscopic examination, in which the mechanically mixed layer (MML) was described. The study of the friction surface roughness parameters confirmed the presence of the formed friction self-lubricating film and allowed to determine its parameters. The friction mechanism was the formation of an oxide layer combined with a solid lubricant, which provides high antifriction properties in the range of 1073–1273 K.
Purpose The aim of the study was to apply and optimize the process of bioconversion of pig bristle waste using keratinolytic enzymes of Bacillus cereus PCM 2849, and to evaluate the amino acid composition of the resultant hydrolysate. Methods Hydrolysis with concentrated culture fluid of B. cereus was applied for bioconversion of pig bristles, after thermo-chemical pretreatment with sulfite. The effect of substrate concentration, sulfite concentration during pretreatment and reaction temperature on the release of amino acids was determined using Box-Behnken design. Amino acid composition of the obtained hydrolysate was determined by HPLC. Structural condition and substructural changes of the residual substrate were evaluated with SEM microscopy and FTIR spectroscopy. Results The applied enzymatic preparation for bristle biodegradation was verified to contain multiple proteases of a wide molecular weight range. A regression model was developed, in which influential parameters were: linear effect of substrate concentration, followed by quadratic effects of reaction temperature, substrate concentration and pretreatment. Optimum reaction conditions were also determined. The resultant hydrolysate was rich in branched-chain amino acids. Residual substrate was detriorated and sulfitolytic cleavage of disulfides and alteration of protein secondary structures was confirmed. Conclusions Application of B.cereus crude keratinase allowed for partial hydrolysis of pig bristles, preceded by sulfitolytic pretreatment. A regression model was built to describe the process of hydrolysis to release free amino acids, at constant enzyme load. Hydrolysis in given conditions allowed to obtain hydrolysate rich in branched chain amino acids. The presented process poses an alternate way of management over pig bristles, a hard-to-degrade keratinous waste.