Finite element modeling of ballistic impact of inserts containing titanium structures were presented in the article. The inserts containing an additional layer made using additive manufacturing technology were analyzed. The layer was created from repetitive elements made without connections (adjacent cells were inseparable). Four variants of printed titanium structures were placed between layers of Twaron CT 750 aramid fabric to create ballistic inserts. In order to assess the ballistic resistance of the inserts, numerical simulations of ballistic impact phenomenon were carried out using LS-Dyna software. In the simulations the inserts were placed on a steel box filled with ballistic clay and were fired at with the 9 × 19 mm full metal jacket (FMJ) Parabellum projectile. The main aim of the work was to check the effectiveness of such solutions in soft ballistic protection applications and to select the most effective variant of 3D printed structure. Results of the numerical analysis showed a high potential for 3D printed structures made of titanium alloys to be used for bulletproof vest inserts. In all analyzed cases the projectile was stopped by the armor. In addition, thanks to the cooperation of adjacent cells, the projectile energy density was distributed over a large area, as evidenced by large volumes of hollows in the ballistic clay. The indentations in the ballistic clay obtained in the simulations were significantly lower than the acceptable value for the back face deformation (BFD) parameter required by international body armor standards.

The paper presents the results of studies on the effects of shooting composite materials produced by pressure infiltration with the EN AW-7075 alloy as a matrix and reinforcement in the form of preforms made of α-Al₂O₃ particles. Composite materials were made with two reinforcement contents (i.e., 30% and 40% vol. of α-Al₂O₃ particles). The composites produced in the form of 12 mm thick plates were subjected to impact loads from a 7.62 × 39 FMJ M43 projectile fired from a Kalashnikov. The samples of composites with different contents of strengthening particles were subjected to detailed microscopic examination to determine the mechanism of destruction. The effect of a projectile impact on the microstructure of the material within the perforation holes was identified. There were radial cracks found around the puncture holes and brittle fragmentation of the front surfaces of the specimens. The change in the volume of the reinforcement significantly affected the inlet, puncture and outlet diameters. The observations confirmed that brittle cracking dominated the destruction mechanism and the crack propagation front ran mainly in the matrix material and along the boundaries of the α-Al₂O₃ particles. In turn, numerical tests were conducted to describe the physical phenomena occurring due to the erosion of a projectile hitting a composite casing. They were performed with the use of the ABAQUS program. Based on constitutive models, the material constants developed from the identification of material properties were modelled and the finite element was generated from homogenization in the form of a representative volume element (RVE). The results of microscopic investigations of the destruction mechanism and numerical investigations were combined. The conducted tests and analyses shed light on the application possibilities of aluminium composites reinforced with Al₂O₃ particles in the construction of add-on-armour protective structures.

In this paper, the authors presented an analysis of the strengthening of the cumulative jet by the appropriate formation of the detonation wave front acting under the influence of high pressure on the liner. The analysis of the Polish ŁK cumulative charge was carried out using numerical methods in the ABAQUS program. Simulation studies were carried out on axial and peripheral initiations of the explosive cumulative liner. For this purpose, two types of cumulative charges were made with the same design parameters, differing only in the explosive detonation-initiation system. The impact of the elastomer insert on the focusing of the cumulative jet was verified. The influence of peripheral and axial initiation on a cumulative jet’s velocity was investigated. The authors proposed a new conical insert placed in the explosive between the pocket for the detonator and the liner, also changing the material of the cumulative liner. The smoothed-particle hydrodynamics method was used to describe the formation of a cumulative jet. The obtained results were verified experimentally, and they show that modification of the ŁK charge has a positive effect on jet amplification, with an inevitable collapse in the final stage of formation. The obtained results correlate with the literature’s data.

This paper discusses the general conditions relating to ballistic head protection, analyzing the risks that may occur on contemporary battlefields. A thorough literature review has enabled us to present development trends for helmets used in the largest armies in the world. The authors have focused on impacts to the helmet shell, overloading the entire helmet-protected head–neck system. The main objective of this study is to investigate the protective capability of a helmet shell when subjected to projectile–helmet contact, with contact curvature taken as being an indicator of the impact energy concentration. Blunt head trauma was estimated using backface deformation (BFD). The Wz.93 combat helmet was used for testing. Analytically, dependencies were derived to determine the scope of BFD. A five-parameter model of the helmet piercing process was adopted, thus obtaining the optimal BFD range. Verification of theoretical considerations was carried out on a specially developed research stand. In the ballistic tests, dynamic deflection of the helmet’s body was registered using a speed camera. On the impact testing stand, a fragment of the helmet was pierced, producing results in the low impact velocity range. Data have been presented on the appropriate graph in order to compare them with values specified in the relevant standard and existing literature. Our results correlate well with the norm and literature values.