The Indonesian National Research and Innovation Agency (BRIN) is currently developing a synthetic aperture radar sensor for a medium-altitude, long endurance aircraft platform for remote sensing applications. The first lab-scale version of the developed SAR system consists of three main parts: transmitter and receiver antennas, an RF subsystem, and a data processing module. The antennas are linearly polarized, and the RF uses a chirp pulsed wave with a 5.3 GHz center frequency and a 150 MHz bandwidth, aiming for 1 m spatial range resolution. The ADC module of the Data Acquisition Unit (DAU) sampled the received baseband IQ signal from the receiver module and saved the complex value into secondary storage, which was then transferred for offline processing. In this paper, we present the implementation of integration between the DAU and the Data Processing Unit (DPU) to optimize signal processing time. With the new design, the current data processing steps can be reduced so that the required time can also be shortened. This will be very useful, especially in field experiments. The design and implementation of a range-matched filtering module as a part of DPU are presented and tested with outdoor SAR experiment data.
This paper presents the design of real-time communication for UAV using an L-band geostationary satellite. The data latency from UAV to GCS and backward are analyzed to broaden the quality of its communication and real-time data. The major data that is used in UAV consists of telemetry, command, and control. Then, all data are passed on a satellite IP network using VPN and UDP protocol link. Four-parameter analyses such as flight mode, attitude response, waypoint response, and joystick response are applied when evaluating data results. The communication link designed in this study is the connectivity between GCS located at Chiba University of Japan and UAV at Pustekbang-LAPAN Bogor, Indonesia. Latency values from several parameters have been presented. Latency data is used to represent real-time data received by GCS to UAV and vice versa. In short, the latency is 2.742 s for manual - auto flight mode, 1.736 s for attitude response right roller, 1.474 s for pitch up, 20.612 s for reading waypoint, and 0.244 s for elevators joystick response. Furthermore, these data will be considered when developing UAV satellite communication systems.
Synthetic Aperture Radar (SAR) can produce high-resolution images and operate in any weather condition, day and night, without a light source. One of the important components that construct an RF SAR sub-system is the IQ Mixer, which mixes the base chirp signal with the carrier signal and increases the bandwidth of the transmitted signal to twice the maximum frequency of the base chirp signal, which is important because the range resolution of SAR depends on the bandwidth of the transmitted signal. This research proposes a LO Phase Shifter design that will be used as a supporting component for IQ Mixer in Synthetic Aperture Radar applications based on a Quadrature Hybrid Ring Coupler. The result from the fabricated measurement shows that the coupler has a good S-parameter value. S11 has a low reflection of -33.85 dB, S41 has a high isolation of -29.56 dB, S21 and S31 have low attenuation with amplitude unbalance of 0.2 dB and phase unbalance of 1.93 degrees. The requirement bandwidth of 150 MHz at the center frequency of 5.5 GHz was also achieved.
Synthetic aperture radar (SAR) is a powerful tool in remote sensing applications that can produce high-resolution images and operate in any weather condition. It is composed of many RF components, such as the IQ mixer, which mixes the base chirp signal (IF) with the carrier signal (LO) and increases the bandwidth of the transmitted signal to twice the maximum frequency of the base chirp signal, reducing the workload of Programmable Field Gate Arrays (FPGA) and increasing the resolution of the SAR system. This research proposes a power combiner–splitter design that will be used as a supporting component to construct the IQ mixer in SAR applications based on a rat-race coupler. The measurement results show that the coupler has good S-parameter values. , , and have a low reflection value below −17 dB, has a high isolation value below −22 dB, and and have a low attenuation value below −4 dB with amplitude unbalance below 0.1 dB and phase unbalance below 1. The 150 MHz requirement bandwidth for the RF signal is also achieved.
This paper presents a prototype design of a C-band (5.3 GHz) microstrip Wilkinson Power Divider (WPD). The WPD is intended to replace the existing commercial po
The mixer is an essential component in RF transceiver subsystems. It has a role in shifting the signal frequency for more convenient processing of up-conversion as well as down-conversion. Despite generating the desired signal, the mixer also generates spurious noise that wastes power and reduces the performance of the overall system. This research proposes the design of a microstrip mixer that can enhance the suppression of spurious signals by utilizing the characteristics of the load resistor termination. The simulation results show that by adding the load resistor, the parasitic electrical field on the diode and the reflection signal inside the mixer can be reduced. The measurement result also validates that the suppression of the spurious signal is enhanced, where the signal-to-noise ratio can reach above 50 dB on the single-balanced mixer and above 60 dB on the double-balanced mixer.