Yanuar Prabowo

Yanuar Prabowo

Auto-generated profile, based on publicly available information

Yanuar Prabowo

National Research and Innovation Agency (BRIN)

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2025 in Bulletin of Electrical Engineering and Informatics
Verified
Journal Article
Open access
PDF file
WWWahyudi Wahyudi
Wahyudi Wahyudi
ISImas Tri Setyadewi
Imas Tri Setyadewi
MSMohammad Amanta Kumala Sakti
Mohammad Amanta Kumala Sakti
YPYanuar Prabowo
Yanuar Prabowo
DHDonatina Miswati Hadiyanti
Donatina Miswati Hadiyanti
JSJosaphat Tetuko Sri Sumantyo
Josaphat Tetuko Sri Sumantyo
This paper presents an experimental examination of how unmanned aerial vehicle (UAV) airframe materials affect the electromagnetic characteristics of the airborne circularly polarized (CP) payload antenna. This study specifically investigates the received signal from the circularly polarized synthetic aperture radar (CP-SAR) antenna installed within the fuselage of the lapan surveillance UAV (LSU). In the airborne CP-SAR experiment, broadband CP microstrip subarray antennas were used along with LSU series airframe material composites comprising E-glass EW-185 and Carbon C522 Twill. The composite specimens were prepared to have the same size and thickness to minimize variability in the comparative analysis. The experimental study measures the transmission loss using S-parameters. At 5.3 GHz, the E-glass EW-185 fiber composite exhibits a material attenuation of -1.5 dB and a circular depolarization of 0.32 dB. The E-glass EW-185 fiber composite exhibits a material attenuation of -1.5 dB and a circular depolarization of 0.32 dB. In contrast, the Carbon C522 Twill fiber composite demonstrates a significantly higher material attenuation of -31.24 dB and a circular depolarization of 10.70 dB. Additionally, this paper examines the radiation pattern measurements of the CP-SAR antenna at various frequencies, providing a comprehensive analysis of the materials' impact on antenna performance.

23 November 2021
Verified
Conference Paper
Closed access
YPYanuar Prabowo
Yanuar Prabowo
IPIwan Nofi Yono Putro
Iwan Nofi Yono Putro
YFYanuar Firmansyah
Yanuar Firmansyah
NCNurul Chasanah
Nurul Chasanah
Abdurrasyid RuhiyatAbdurrasyid Ruhiyat
Abdurrasyid Ruhiyat
CSCahya Santosa
Cahya Santosa
This paper presents the design of real-time communication for UAV using an L-band geostationary satellite. The data latency from UAV to GCS and backward are analyzed to broaden the quality of its communication and real-time data. The major data that is used in UAV consists of telemetry, command, and control. Then, all data are passed on a satellite IP network using VPN and UDP protocol link. Four-parameter analyses such as flight mode, attitude response, waypoint response, and joystick response are applied when evaluating data results. The communication link designed in this study is the connectivity between GCS located at Chiba University of Japan and UAV at Pustekbang-LAPAN Bogor, Indonesia. Latency values from several parameters have been presented. Latency data is used to represent real-time data received by GCS to UAV and vice versa. In short, the latency is 2.742 s for manual - auto flight mode, 1.736 s for attitude response right roller, 1.474 s for pitch up, 20.612 s for reading waypoint, and 0.244 s for elevators joystick response. Furthermore, these data will be considered when developing UAV satellite communication systems.

1 February 2024 in International Journal of Electrical and Computer Engineering (IJECE)
Verified
Journal Article
Open access
PDF file
ISImas Tri Setyadewi
Imas Tri Setyadewi
YPYanuar Prabowo
Yanuar Prabowo
PWPriyo Wibowo
Priyo Wibowo
PPPurnomo Sidi Priambodo
Purnomo Sidi Priambodo
The increasing complexity of electrical and electronic systems in unmanned aerial vehicles (UAVs) has raised concerns regarding unwanted electromagnetic interference (EMI) due to limited compartment space. Recent studies have highlighted the UAV cabling as the primary pathway for interference. This paper presents a novel approach to investigating the effects of interference power, polarization angle, and distance from the interference source on EMI in UAV cable systems. Measurements and simulations were performed to analyze the influence of these factors on the radiation received by the cable. A linear dipole antenna, operating at a frequency of 905 MHz, served as the radiation source, while a single wire cable pair terminated with a 50-ohm resistor was employed as the victim. The findings reveal that the power transmitted by the source, the distance between the cable and the source, and the polarization angle have a significant impact on the electromagnetic interference received by the cable. Notably, a perpendicular orientation of the cable to the interference source (antenna) in the far-field yielded a reduction of up to 15 dBm in EMI. The results underscore the necessity for more sophisticated models and comprehensive measurements to fully comprehend the diverse factors affecting polarization losses in practical scenarios.

30 June 2025 in Jurnal Teknik Elektro
Verified
Journal Article
Open access
PDF file
YPYanuar Prabowo
Yanuar Prabowo
ISImas Tri Setyadewi
Imas Tri Setyadewi
MSMohammad Amanta Kumala Sakti
Mohammad Amanta Kumala Sakti
YGYomi Guno
Yomi Guno
WAWahyudi
Wahyudi
CSCahya Edi Santosa
Cahya Edi Santosa
This study aims to mitigate the impact of electromagnetic interference on the performance of electronic systems in Unmanned Aerial Vehicles (UAVs) by employing various shielding materials. The materials tested include carbon fiber, E-glass, E-glass with an aluminium foil, and E-glass with a copper foil. A Vector Network Analyzer (VNA) and scattering parameter (S-Parameter) analysis, including reflection, absorption, and multiple reflection, were used to evaluate the shielding effectiveness of these materials within the frequency range of 4 - 5 GHz. The results showed that E-glass coated with copper had good overall shielding performance for SER, SEA, and SET values. This material reached a SET value of 96 dB at a frequency of 4.6 GHz, followed by E-glass coated with aluminium. In addition, adding carbon layers increased the shielding effectiveness, while E-glass without coating had the lowest shielding performance compared to the other materials. These findings indicate that E-glass coated with metal provides superior shielding effectiveness compared to carbon fiber, even when used in greater thickness.