Javier Molina Salazar

Dr. Javier Molina Salazar

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 June 2025 in Electronics
Verified
Journal Article
Open access
PDF file
GPGeu Misael Puentes
Geu Misael Puentes
Ernesto SifuentesErnesto Sifuentes
Ernesto Sifuentes
JSJavier Molina Salazar
Javier Molina Salazar
FEFrancisco Enriquez
Francisco Enriquez
GBGabriel Bravo
Gabriel Bravo
GEGuadalupe Navarro Enríquez
Guadalupe Navarro Enríquez
Direct interface circuits (DICs) connect resistive, capacitive, and inductive sensors directly to microcontrollers or FPGAs, eliminating analog conditioning stages and offering compact, low-cost, and low-power instrumentation. This systematic review qualitatively synthesizes research up to March 2025 on DIC operation principles, performance metrics, and application domains. Following PRISMA guidelines, 90 studies from IEEE Xplore, ScienceDirect, MDPI, SpringerLink, Scopus, and Google Scholar were selected based on predefined inclusion criteria. Most studies focused on RC-based circuits (53%), followed by RL-based (5%) and charge transfer capacitive interfaces (5%). RC-DICs demonstrated accuracies below 0.01% using adaptive calibration; RL-DICs achieved resolutions of 10–12 bits with higher cycle requirements, while charge transfer interfaces presented systematic errors up to ±5% due to parasitic capacitances. Environmental monitoring, biomedical sensing, liquid-level control, and vehicular detection were frequent application fields. Due to methodological heterogeneity, findings were synthesized qualitatively without quantitative meta-analysis or formal bias assessments. Future research directions include enhanced noise immunity, simplified calibration, and robust parasitic effect compensation.

17 May 2025 in Preprints.org
Verified
Preprint
Open access
PDF file
GPGeu Misael Puentes
Geu Misael Puentes
Ernesto SifuentesErnesto Sifuentes
Ernesto Sifuentes
JSJavier Molina Salazar
Javier Molina Salazar
FEFrancisco Enriquez
Francisco Enriquez
GBGabriel Bravo
Gabriel Bravo
GEGuadalupe Navarro Enríquez
Guadalupe Navarro Enríquez
This paper presents a comprehensive review of Direct Interface Circuits (DICs), which provide a compact, cost-effective, and energy-efficient alternative for interfacing with sensors that exhibit electrical variations such as resistance, capacitance, and inductance. A distinctive characteristic of DICs is their ability to connect sensors directly to digital processors, including microcontrollers (MCUs) or Field-Programmable Gate Arrays (FPGAs), through RC, RL, or capacitive charge transfer configurations, without the need for additional signal conditioning components. The review outlines the fundamental operating principles and key elements of DICs, including time-to-digital conversion, digital processing, and techniques for assessing measurement accuracy, resolution, response time, and the effects of uncertainty and interference. By synthesizing findings from recent literature, this study provides an in-depth understanding of current advancements in DICs and offers a critical analysis of their state-of-the-art implementations. Finally, strategic recommendations are proposed to guide future research directions and application areas.

28 February 2025 in Journal of Applied Research and Technology
Verified
Journal Article
Open access
PDF file
LRL. Rico-Pérez
L. Rico-Pérez
MZM. A. Zalapa-Garibay
M. A. Zalapa-Garibay
JSJavier Molina Salazar
Javier Molina Salazar
CMChristian Marisol Clemente Mirafuentes
Christian Marisol Clemente Mirafuentes
This paper presents an analysis and mathematical modeling of the cutting parameters in the turning process of 1018 steel material. For this analysis, an experiment was designed using 40 specimens of 1" diameter by 6" long. In this experiment, the control parameters were cutting speed in revolutions per minute (rpm), feed rate in inches per minute (inches/minute) and depth of cut in inches (inches), while the response variable is surface roughness in micro inches (µinches). The results show that the feed rate, cutting speed and the interaction between feed rate and cutting speed affect the surface roughness of the workpiece. Finally, with the RStudio software, a mathematical model was obtained with an R2 equal to 0.99, a value very close to previous experimental works and, in addition, a good predictor of surface roughness.

26 September 2018 in REVISTA DE CIENCIAS TECNOLÓGICAS
Verified
Journal Article
Open access
PDF file
MRManuel-Javier Rosel-Solis
Manuel-Javier Rosel-Solis
JSJavier Molina Salazar
Javier Molina Salazar
JPJUAN ANTONIO PAZ
JUAN ANTONIO PAZ
JOJuan Antonio Ruiz Ochoa
Juan Antonio Ruiz Ochoa
En el presente trabajo se revisa el estado del arte que guarda la manufactura aditiva en cuanto a sus avances en la mejora de sus materiales, específicamente, a través de la incorporación de materiales compuestos, como la fibra de carbono. Además, se hace una revisión de los procesos convencionales de manufactura de materiales compuestos y se analiza el grado de aplicación de la manufactura aditiva y los materiales compuestos en la manufactura de prótesis transtibiales prostéticas y de uso deportivo, con el objetivo de identificar oportunidades de mejora.

1 May 2019 in DYNA Ingenieria e Industria
Verified
Journal Article
Closed access
MRManuel-Javier Rosel-Solis
Manuel-Javier Rosel-Solis
JSJavier Molina Salazar
Javier Molina Salazar
JRJose Omar Davalos Ramirez
Jose Omar Davalos Ramirez
AMAlex Bernardo Pimentel Mendoza
Alex Bernardo Pimentel Mendoza
YVYuridia Vega
Yuridia Vega

1 May 2022 in DYNA Ingenieria e Industria
Verified
Journal Article
Closed access
JSJavier Molina Salazar
Javier Molina Salazar
SLSecundino Lozano Lozano
Secundino Lozano Lozano
MMManuel Rodríguez Medina
Manuel Rodríguez Medina
EOEduardo Rafael Poblano Ojinaga
Eduardo Rafael Poblano Ojinaga
Advanced manufacturing technologies, coupled with consumer demands for more customized products and services, are driving changes in the scale and distribution of manufacturing.