Interactions between an oblique shock wave generated by a sharp fin placed on a cylindrical surface and the incoming boundary layer are investigated to unravel the mean features of the resulting shock/boundary layer interaction (SBLI) unit. This fin-on-cylinder SBLI unit has several unique features caused by the three-dimensional (3-D) relief offered by the cylindrical surface that noticeably alter the shock structure. Complementary experimental and computational studies are made to delineate both the surface and off-body flow features of the fin-on-cylinder SBLI unit and to obtain a detailed understanding of the mechanisms that dictate the mean flow and wall pressure features of the SBLI unit. Results show that the fin-on-cylinder SBLI exhibits substantial deviation from quasi-conical symmetry that is observed in planar fin SBLI. Furthermore, the separated flow growth rate appears to decrease with downstream distance and the separation size is consistently smaller than the planar fin SBLI with the same inflow and fin configurations. The causes for the observed diminution of the separated flow and its downstream growth rate were investigated in the light of changes caused by the cylinder curvature on the inviscid as well as separation shock. It was found that the inviscid shock gets progressively weakened in the region close to the triple point with downstream distance due to the 3-D relief effect from cylinder curvature. This weakening of the inviscid shock feeds into the separation shock, which is also independently impacted by the 3-D relief, to result in the observed modifications in the fin-on-cylinder SBLI unit.
Unstart of rectangular inlets occurs as a result of interactions between shock-induced separation units along the floor/ceiling, corner, and sidewalls. While a significant body of literature exists regarding the individual flow interactions at the inlet floor/ceiling (called primary separation) and sidewalls, limited efforts have focused on the mean and dynamic features of the corner separation. Experiments are conducted to investigate primary and corner shock boundary layer interactions (SBLI) with the objectives of elucidating the flow interactions that occur in the corner, and characterizing the interaction between the corner and primary separation units at mild back pressure ratios. Surface streakline flow visualization and high-frequency wall static pressure measurements are performed along the centerline and corner regions of shock-induced flow separation generated by a 12° compression ramp in a Mach 2.5 flow. Sidewall fences that extend upstream of the leading edge of the flat plate generate corner separation of adequate size to determine the mean flow structures, characterize the unsteady motions, and investigate the mechanisms that drive the unsteadiness of primary and corner SBLI. Results show that the corner and primary SBLI units differ fundamentally in both their mean and unsteady features and their response to upstream and downstream flow perturbations. These observations suggest that the two behave as independent units at this relatively low shock-induced back pressure ratio.
The large-scale pulsations of shock-induced separation with length scale that significantly exceeds the incoming boundary layer thickness are investigated. The shock–boundary layer interaction (SBLI) unit is generated by an inward-turning axisymmetric compression ramp at an inflow Mach number of 2.5. A substantial region surrounding the centre azimuth exhibited mean and dynamic flow features that are consistent with two-dimensional separation. Two-dimensional highly resolved maps of surface pressure field are obtained using fast-response pressure-sensitive paint fluorescence imaging at 40 kHz repetition rate. The measurement domain covered significant regions of the incoming boundary layer through the relaxing boundary layer downstream of the reattachment as well as over 25 boundary layer thicknesses in the azimuthal direction. These measurements provide new insights into the spanwise coupling of the SBLI unit in addition to its inherent dynamics. The power spectral density (PSD) of the centreline pressure exhibits very good agreement with theoretical models and complementary measurements using fast-response pressure transducers, which served to validate the pressure field measurements. Detailed examination of the PSD reveals strong agreement with the literature, which includes the peak Strouhal number of the separation and reattachment shock motions as well as the downward frequency shift along the separation bubble. Furthermore, the pressure fluctuation maps reveal streamwise-elongated structures just downstream of the ramp leading edge that persist well downstream of the reattachment. A time sequence of conditional average pressure fluctuation maps is constructed surrounding isolated pressure excursions in the intermittent region. This sequence, along with two-point cross correlation analysis, provides critical information about the flow processes that drive the separation bubble pulsations in the SBLI units with large separation scales. Overall, the imbalance in the mass within the separation bubble appears to be the critical mechanism that drives the separation bubble pulsations. Furthermore, the pressure perturbations originating at azimuthally offset locations are also observed to influence the separation bubble dynamics.
Shock oscillations within a model two-dimensional axisymmetric inlet with a constant area isolator are investigated under the condition of maintaining an unseparated boundary layer throughout the inlet/isolator section. Power spectral densities of the wall-pressure fluctuations beneath each shock leg intersecting the isolator surface exhibited a very low frequency broadband oscillation in the 10–100 Hz range as well as a very high frequency broadband oscillations above 10 kHz. Whereas the high frequency oscillations are attributed to the incoming boundary layer fluctuations, detailed investigations into the pressure fluctuation communication pathways within the isolator and their length scale of communication are made to elucidate the origin of the low frequency fluctuations. It was found that the downstream propagation of pressure fluctuations is primarily by the convection of the boundary layer structures and this communication occurred over several boundary layer thicknesses. The upstream propagation occurs through acoustic waves that extend over a distance of one local boundary layer thickness. Based on this understanding, a physical model is constructed, which makes an accurate prediction of pressure power spectrum of the low frequency shock wave oscillations; the model predictions also favourably compare with the shock oscillations in external shock boundary layer interactions without shock-induced flow separation.
Stream-traced inlets offer superior compression efficiency for scramjet engines and are strong prospects for practical application. However, only limited experimental information is available on the subdesign performance of these inlets. In this study, the operation of a stream-traced truncated-Busemann inlet with a design point of Mach 5.5 and a physical contraction ratio of [ ] is experimentally investigated in a Mach 4.0 flow. Several nonintrusive flow measurement techniques are employed to provide a thorough understanding of the intricate flowfield within these inlets at various operation conditions. The measurements include surface pressure, mean streak-line patterns, off-body velocity fields, and qualitative gas density fields. Together, these datasets provided a unique understanding of the flow evolution and load distribution within the inlet and isolator with and without application of an external backpressure. The facility effects on the inlet operation are also explored. Without appropriate boundary-layer conditioning, the wind-tunnel starting shock could not be swallowed by the inlet; this is termed a “failed start” operation. During the failed start operation the inlet flowfield and surface pressure field, even without external backpressure, exhibited strong similarities with an unstarted inlet. The failed start operation enabled a unique lens to the flowfield in the unstarted inlet throat that could not be otherwise obtained due to optical constraints.