Ceramic matrix composites have the advantages of low density, high specific strength, high specific die, high-temperature resistance, wear resistance, chemical corrosion resistance, etc., which are widely used in aerospace, energy, transportation, and other fields. CMCs have become an important choice for engine components and other high-temperature component manufacturing. However, ceramic matrix composite is a kind of multi-phase structure, anisotropy, high hardness material, due to the brittleness of the ceramic matrix, the weak bonding force between fiber and matrix, and the anisotropy of composite material. Burr, delamination, tearing, chips, and other surface damage tend to generate in the machining, resulting in surface quality and strength decline. This paper reviewed the latest abrasive machining technology for SiC ceramic composites. The characteristics and research directions of the main abrasive machining technology, including grinding, laser-assisted grinding, ultrasonic-assisted grinding, and abrasive waterjet machining, are introduced first. Then, the commonly used numerical simulation research for modeling and simulating the machining of ceramic matrix composites is briefly summarized. Finally, the processing difficulties and research hotspots of ceramic matrix composites are summarized.

Bulk metallic glasses (BMGs) deform irreversibly through shear banding manifested as serrated-flow behavior during compressive tests. The strain-rate-dependent plasticity under uniaxial compression at the strain rates of 2 × 10⁻², 2 × 10⁻³, and 2 × 10⁻⁴·s⁻¹ in a Pd-based BMG is investigated. The serrated flow behavior is not observed in the stress-strain curve at the strain rate of 2 × 10⁻²·s⁻¹. However, the medial state occurs at the strain rates of 2 × 10⁻³·s⁻¹, and eventually the self-organized critical (SOC) behavior appears at the strain rate of 2 × 10⁻⁴·s⁻¹. The distribution of the elastic energy density shows a power-law distribution with the power-law exponent of −2.76, suggesting that the SOC behavior appears. In addition, the cumulative probability is well approximated by a power-law distribution function with the power-law exponent of 0.22 at the strain rate of 2 × 10⁻⁴·s⁻¹. The values of the goodness of fit are 0.95 and 0.99 at the strain rates of 2 × 10⁻³ and 2 × 10⁻⁴·s⁻¹, respectively. The transition of the dynamic serrated flows of BMGs is from non-serrated flow to an intermediate state and finally to the SOC state with decreasing the strain rates.

The strain-rate-dependent plasticity under uniaxial compression at the strain rates of 2 × 10⁻³, 2 × 10⁻⁴ and 2 × 10⁻⁵ s⁻¹ in a Pd_77.5Cu₆Si_16.5 alloy is investigated. At different strain rates, the serration events exhibit different amplitudes and time scales. The intersection effects take place obviously, and the loading time is much longer than the relaxation time in the serration event at three strain rates. However, the time intervals between two neighboring serrations lack any time scale, and the elastic energy density displays a power-law distribution at the strain rate of 2 × 10⁻³ s⁻¹, which means that the self-organized critical (SOC) behavior emerges with increasing strain rates.

The incorporation of various types of fillers is critical to enhancing the starved oil lubrication performance of PEEK matrix composites. In this work, PEEK composites reinforced with h-BN and SCFs were fabricated via a hot-pressing method, and the friction and wear behaviors under dry sliding and starved oil lubrication were systematically investigated. Surface oil wettability and Vickers hardness were characterized, and tribological tests were conducted on a ball-on-disk reciprocating tribometer. Worn surface topography and wear mechanisms were elucidated through laser scanning confocal microscopy and scanning electron microscopy. The results show that h-BN effectively reduces the friction coefficient through its solid lubrication effect, while SCFs significantly improve the hardness and load-bearing capacity of the PEEK matrix. Under dry sliding conditions, the PEEK composite containing h-BN and SCFs achieves the lowest wear rate of 10.3 × 10⁻⁵ mm³/(N·m), which is 74.6% lower than that of pure PEEK, indicating a synergistic anti-wear effect. Under starved oil lubrication, PEEK/h-BN maintains the smoothest and lowest friction, and the presence of SCFs further improves wear resistance of PEEK composites despite a slight increase in friction. In addition, the fillers’ incorporation reduces the surface oil wettability of the PEEK composites; the dominant wear mechanism hence transforms from severe adhesive wear and plastic deformation in pure PEEK to mild abrasive wear.

Enhanced plasticity is obtained in a structurally rejuvenated Zr-based bulk metallic glass (BMG) that has been treated via cryogenic thermal cycling (CTC) for one hundred cycles. More than one primary shear band is activated due to the structural rejuvenation, which can inhibit the jerky and system-spanning propagation of shear bands to generate sluggish shear-dynamics. These are mapped to the slip statistics, including the decreased critical avalanche size, the much longer avalanche duration of large (system-spanning) slips, and a great number of small avalanches. Moreover, the universal scaling of slip avalanches for three applied stress ranges is addressed to predict the applied stress at which the failure avalanche appears most. These results indicate that slip statistics can be the fingerprints to show how much the BMG is rejuvenated, and the failure avalanche provides a good opportunity to intervene in the failure of BMGs in advance.