A compact single-layer textile MIMO antenna is designed for wearable applications. The theory of characteristic mode is used to guide the antenna design and analyze its performance. The MIMO antenna utilizes a small ground plane as the main radiator, which is capacitively loaded by two strips along two orthogonal edges. The whole system occupies a volume of 38.1 mm × 38.1 mm × 2 mm, with each antenna having a dipole-like radiation pattern of linear polarization. Good isolation of above 12 dB is achieved due to the quasi-orthogonal radiations generated by the two antennas, providing pattern and polarization diversities. The envelope correlation coefficient between the antennas is below 0.01. The proposed antenna, fabricated on a flexible felt with a permittivity of 1.2, has a wide bandwidth of 20%. Due to its broadband behavior, the antennas remain well matched at the target band when worn on the body and bended. The loss of the human tissue results in the drop of the antenna gains to 1.6 dBi and 1.2 dBi, respectively, for the two antennas. The proposed antenna is competitive for wearable applications, due to its compact size, single-layer structure, easy integration, robustness, and reasonable on-body antenna gain.
In this work, the subgrid-scale (SGS) stress and the SGS heat flux of compressible isotropic turbulence are modeled by an artificial neural network (ANN) mixed model (ANNMM), which maintains both functional and structural performances. The functional form of the mixed model combining the gradient model and the Smagorinsky’s eddy viscosity model is imposed, and the ANN is used to calculate the model coefficients of the SGS anisotropy stress, SGS energy, and SGS heat flux. It is shown that the ANNMM can reconstruct the SGS terms more accurately than the gradient model in the a priori test. Specifically, the ANNMM almost recovers the average values of the SGS energy flux and SGS energy flux conditioned on the normalized filtered velocity divergence. In an a posteriori analysis, the ANNMM shows advantage over the dynamic Smagorinsky model (DSM) and dynamic mixed model (DMM) in the prediction of the spectra of velocity and temperature, which almost overlap with the filtered direct numerical simulation data, while the DSM and DMM suffer from the problem of the typical tilted spectral distribution. Besides, the ANNMM predicts the probability density functions of SGS energy flux much better than DSM and DMM. ANN with functional model forms can enlighten and deepen our understanding of large eddy simulation modeling.
23 November 2018 in Journal of Physics D: Applied Physics
The characteristics of molten pools provide valuable insight into the complexity of the metal additive manufacturing process, which has a significant influence on the quality of the parts built using this process. In our work, we develop a three-dimensional multiphysics finite element model of a selective laser melting (SLM) process on a Ti–6Al–4V alloy. The dynamic characteristics of the molten pool are studied by multiphysics simulation with consideration of phase transitions, recoil pressure, surface tension, and Marangoni effect. The results show the time-evolution of temperature distribution, flow field, and surface morphology of a single track during the SLM process. The recoil pressure caused by evaporation plays a significant role in molten pool dynamics and induces a depression at the head of the molten pool. As a result of the backward Marangoni flow, the material is shifted to the tail region and a vortex is generated. In addition, a protrusion is presented at the middle and start points of the scanned track, while a depression is formed at both sides and at the terminal point. The simulation and the experimental results on the surface morphology of the molten track during the SLM process are in good agreement. Furthermore, it is found that metal evaporation may take place not only on the surface of the molten pool but also inside it, due to the drop in pressure. This is a significant contributor to the formation of porosity in SLM parts.
2 August 2021 in Journal of Intelligent Manufacturing
In this communication, a compact pattern reconfigurable dual-antenna array is designed at 2.65 GHz for multiple-input multiple-output (MIMO) terminal applications, such as laptops. Each antenna is composed of two layers, i.e., the monopole layer and the planar inverted-F antenna (PIFA) layer. By switching the p-i-n diodes on each layer, its radiation patterns can be varied between conical and boresight patterns. Two such identical antennas are placed side by side on a common ground plane for MIMO application, providing altogether four operating modes. The center-to-center separation between the antennas is 0.25 wavelength, to keep the overall array compact. To facilitate an isolation of above 17 dB over all the modes for this compact array, two decoupling techniques based on the decoupling slits and the shielding wall are effectively combined. The envelope correlation coefficients (ECCs) of the far-field patterns in the four modes are below 0.05 in free space, and below 0.1 for most cases in the indoor and outdoor scenarios. The only exception is the monopole-PIFA mode in the outdoor scenario, but the ECC is still below 0.3 for this case. The measured efficiencies of the antennas are between -1.7 (68%) and -0.7 dB (85%) for all the modes. Therefore, good diversity and MIMO performances are expected for the proposed design.
30 November 2020 in IEEE Transactions on Vehicular Technology
In this work, wideband dual-polarized dielectric resonator antenna (DRA) arrays are designed for 5G mobile handsets and integrated with the sub-6GHz antenna. The dielectric resonators, surrounded by concentric air holes and metal vias, are excited by two orthogonal slots and fed through microstrip lines, providing a wide bandwidth from 25.3 GHz to 29.8 GHz. A high isolation of above 40 dB is obtained between the ports of the orthogonally polarized antennas. Based on the dual-polarized DRA, two 14 arrays are built and integrated with the longer metal frames of the handset, without occupying extra space on the chassis. The scanning angle for the proposed array is from 47 to 121 for the gain of above 10 dBi, and the overall handset antennas provide a large coverage efficiency of 80 % for a threshold gain of 5 dBi. User effect has also been investigated, manifesting that the horizontally polarized antennas are less influenced by the hands in both the one-hand and the two-hand data modes. Furthermore, a sub-6GHz antenna is designed with a wide operating band from 0.7 GHz to 0.94 GHz simply by making use of the shorter frames and the dual-layered DRAs, with a small ground clearance of 2mm remained. The performances of the arrays are validated by measuring the representative antennas. The proposed antenna is a good candidate for future handsets due to its high integration with the metal frames and with the LTE antenna, its large bandwidth and large coverage in free space and different user scenarios.