Laura Cabezas

Ms. Laura Cabezas

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 April 2024 in Acta Materialia
Verified
Journal Article
Closed access
ZAZahid Anwer
Zahid Anwer
LCLaura Cabezas
Laura Cabezas
EJE. Jiménez-Piqué
E. Jiménez-Piqué
LLLuis Llanes
Luis Llanes
JVJef Vleugels
Jef Vleugels
SHShuigen Huang
Shuigen Huang

19 December 2022 in Metals
Verified
Journal Article
Open access
PDF file
MMMiguel Morales
Miguel Morales
LCLaura Cabezas
Laura Cabezas
MCManuel Castro-Alloca
Manuel Castro-Alloca
GFGemma Fargas
Gemma Fargas
LLLuis Llanes
Luis Llanes
Antonio MateoAntonio Mateo
Antonio Mateo
Next-generation concentrated solar power (CSP) plants are required to operate at temperatures as high as possible to reach a better energy efficiency. This means significant challenges for the construction materials in terms of corrosion resistance, among others. In the present work, the corrosion behavior in a molten eutectic ternary Li2CO3-Na2CO3-K2CO3 mixture at 600 °C was studied for three stainless steels: an austenitic grade AISI 301LN (SS301) and two duplex grades, namely 2205 (DS2205) and 2507 (DS2507). Corrosion tests combined with complementary microscopy, microanalysis and mechanical characterization techniques were employed to determine the corrosion kinetics of the steels and the oxide scales formed on the surface. The results showed that all three materials exhibited a corrosion kinetics close to a parabolic law, and their corrosion rates increased in the following order: DS2507 < SS301 < DS2205. The analyses of the oxide scales evidenced an arranged multilayer system with LiFeO2, LiCrO2, FeCr2O4 and NiO as the main compounds. While the Ni-rich inner layer of the scales presented a good adhesion to the metallic substrate, the outer layer formed by LiFeO2 exhibited a higher concentration of porosity and voids. Both the Cr and Ni contents at the inner layer and the defects at the outer layer were crucial for the corrosion resistance for each steel. Among the studied materials, super duplex stainless steel 2507 is found to be the most promising alternative for thermal energy storage of those structural components for CSP plants.

13 March 2024 in Ceramics International
Verified
Journal Article
Closed access
JZJunhui Zhang
Junhui Zhang
MSMarc Serra
Marc Serra
SESergio Elizalde
Sergio Elizalde
Mona YarahmadiMona Yarahmadi
Mona Yarahmadi
LCLaura Cabezas
Laura Cabezas
LLLuis Llanes
Luis Llanes

20 June 2024 in Crystals
Verified
Journal Article
Open access
PDF file
LCLaura Cabezas
Laura Cabezas
CBChristian Berger
Christian Berger
Emilio Jiménez PiqueEmilio Jiménez Pique
Emilio Jiménez Pique
JPJohannes Pötschke
Johannes Pötschke
LLLuis Llanes
Luis Llanes
Binder jetting additive manufacturing offers a promising route to produce complex geometries in cemented carbides (WC-Co), but it may introduce direction-dependent microstructural variations potentially affecting wear resistance. This study investigates the influence of printing direction on the sliding contact response of 3D-printed and subsequently sintered (BJT) WC-12%Co. Prismatic specimens were printed along two orientations and subjected to single and repetitive scratch tests on three orthogonal faces. The microstructure, Vickers and scratch hardness, and wear rate were analyzed. The results showed a heterogeneous microstructure consisting of a matrix of fine carbides where several large particles where embedded. It was different from the homogenous microstructural scenarios exhibited by conventionally pressed and sintered fine- and coarse-grained hardmetals, used as reference for comparison purposes. The influence of printing direction on either the microstructure or mechanical properties of BJT specimens was found to be negligible. Interestingly, BJT samples exhibited superior wear resistance than the reference hardmetals, even though the hardness levels were alike for all the studied hardmetal grades. Such behavior is attributed to the co-existence of coarse and fine carbides within the microstructure, combining the energy absorption capability of the former with the inherent strength of the latter. These findings, together with the intrinsic flexibility and versatility advantages associated with additive manufacturing, highlight the potential of BJT hardmetals to be used in applications where contact load bearing or wear resistance are critical design parameters. Finally, the effectiveness of implementing an iterative sliding contact test for evaluating wear behavior in cemented carbides was also validated.

28 May 2026 in SSRN Electronic Journal
Verified
Preprint
Open access
MCMartina Cera
Martina Cera
LCLaura Cabezas
Laura Cabezas
GGGian Pietro De Gaudenzi
Gian Pietro De Gaudenzi
STSandra Tedeschi
Sandra Tedeschi
ASAngela Serpe
Angela Serpe
LLLuis Llanes
Luis Llanes
Hardmetal (HM) sector faces growing supply risks due to the criticality of tungsten (W) and cobalt (Co), the main components of WC–Co cemented carbides. To reduce dependence on raw material suppliers, recycling of HM waste is becoming increasingly important, and sustainable recovery processes are being developed to meet both environmental regulations and industrial demands. The properties of HMs are strongly influenced by microstructural features such as WC grain size, binder content, and possible residual phases, which are not always easy to control in new recycling systems. In this study, WC–Co samples were produced entirely from recycled scraps through an oxidation–reduction–carburization treatment combined with eco-friendly leaching based on organic acids. Microstructural analysis and mechanical tests showed that the recycling process does not significantly affect the main microstructural parameters or the mechanical performance, apart from minor differences in WC grain morphology. These results demonstrate that fully recycled WC–Co HMs can achieve quality standards comparable to conventional materials.

19 August 2026 in Open Ceramics
Verified
Journal Article
Open access
LCLaura Cabezas
Laura Cabezas
SHS. Huang
S. Huang
EJE. Jiménez-Piqué
E. Jiménez-Piqué
PMP. Moreno
P. Moreno
JVJ. Vleugels
J. Vleugels
LLL. Llanes
L. Llanes