Ather Syed

Mr. Ather Syed


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 September 2025 in Solids
Verified
Journal Article
Open access
PDF file
ASAther Syed
Ather Syed
Mahendra Kumar SamalMahendra Kumar Samal
Mahendra Kumar Samal
Nuclear fuel cladding serves as the primary barrier to the release of radioactive fission products and is subjected to high-temperature and high-pressure environments during both normal reactor operation and accident scenarios such as loss of coolant accidents (LOCAs). Predicting the burst behavior of cladding is essential for ensuring structural integrity, especially under varying heating rates—an aspect inadequately addressed in existing empirical models. In this study, a finite element-based damage model is developed to simulate the ballooning and burst behavior of Zircaloy-4 cladding. The model incorporates creep deformation, stress triaxiality, and time-dependent damage accumulation. Material behavior is characterized using experimentally determined creep constants and the model is calibrated against burst test data from the literature. A new heating-rate-dependent burst correlation is proposed based on model outputs. The results indicate that increasing the heating rate raises the burst temperature due to reduced exposure time in the temperature regime where creep damage accumulates significantly. The model accurately reproduces burst behavior across a wide range of internal pressures (1–10 MPa) and heating rates (5–100 °C/s). The newly developed correlation improves predictive capability in accident analysis tools and can be directly implemented into safety analysis codes for Indian pressurized heavy water reactors (PHWRs), contributing to enhanced reactor safety evaluations.

30 June 2025 in Preprints.org
Verified
Preprint
Open access
PDF file
ASAther Syed
Ather Syed
Mahendra Kumar SamalMahendra Kumar Samal
Mahendra Kumar Samal
Nuclear fuel clad are thin-walled tubes containing fuel pellets generating heat during operation of reactor, and also during dry storage due to decay heat. The clad is subjected to high temperature and high pressure environment during various postulated accident scenarios. As the fuel clad acts as a barrier to radioactive release, the clad burst becomes a critical criteria for its integrity assessment. Clad burst experiments have been carried out by various researchers for various combinations of internal pressure and heating schemes. Several empirical correlations are reported in literature for prediction of clad burst stress as a function of burst temperature. These empirical correlations do not account for variation in heating rates on clad burst behavior. In this work, a new damage model has been used to predict the burst behavior of fuel clad for various heating rates. A new correlation has been proposed which takes into account of the heating rates. It was observed that by increasing the heating rate, the burst temperature gets elevated as the time for accumulation of material damage becomes less. The correlation has also been validated with experimental data from literature. This new correlation can be used in severe accident analysis codes to predict the fuel pin burst phenomenon accurately.

21 May 2024 in Preprints.org
Verified
Preprint
Open access
PDF file
Mahendra Kumar SamalMahendra Kumar Samal
Mahendra Kumar Samal
Trishant SahuTrishant Sahu
Trishant Sahu
ASAther Syed
Ather Syed
Aluminium alloys are used for fabrication of fuel clad of research grade nuclear reactors as well as of several types of core components of high flux research reactors. In order to carry out design and safety analysis of these components, their mechanical and fracture properties are required by the designer. In this work, experiments have been conducted on tensile specimens machined from an aluminium alloy block to evaluate the material stress-strain curve. For evaluation of fracture properties, experiments have been conducted on disc shaped compact tension specimens in order to determine the fracture toughness of aluminium alloy. From crystal plasticity based finite element analysis and experimental data, a material damage parameter for prediction of crack initiation has been evaluated. The variation of the parameter for various values of initial a/W ratios of the disc-shaped CT specimens have been studied. It was observed that the damage parameter is independent of crack geometry and hence, it qualifies as transferable material property which can be used to predict crack initiation in a component of this material subjected to different kinds of loading conditions. In addition, the JR curves of the disc-shaped CT specimens have also been evaluated from experiments. The material damage parameter has also been used to study the crack initiation in single crystal fracture specimens with two different orientations. It was observed that the [111] orientation is more susceptible to crack initiation and propagation compared to the [100] orientation as the damage parameter is high in the ligament of the specimen ahead of the crack-tip for the same level of load. The results of the experiments and the material damage parameter shall be helpful for integrity analysis of fuel clad of research reactors as well as components of high flux research reactors.

9 April 2026 in Preprints.org
Verified
Preprint
Open access
PDF file
ASAther Syed
Ather Syed
Mahendra Kumar SamalMahendra Kumar Samal
Mahendra Kumar Samal
Pressure tubes (channels containing fuel in CANDU type nuclear reactors) of Indian pressurized heavy water reactors are made from quadruple-melted Zr-2.5Nb alloy. Owing to the texture and crystal structure, these tubes exhibit anisotropy in mechanical properties. During postulated severe accident scenario such as loss of coolant accident, the temperature of the pressure tube may rise rapidly due to disruption in the heat removal porcess from the fuel bundles. The deformation behavior of the pressure tube under such high temperature shall effect the integrity of the coolant channel. Hence, it is crucial to model the high temperature deformation behavior of pressure tube under these conditions. For design and safety analysis of pressure tube, the high temperature properties are required. In this work, tensile tests were carried out using the specimens cut from quadruple melted Zr2.5%Nb pressure tube along longitudinal, transverse and radial directions at temperatures, i.e., from 25˚C to 800˚C. Shear properties were also evaluated by using the specimen machined from longitudinal-circumferential orientation of tube. It was observed that the specimen oriented along the circumferential direction has highest strength, while the radial specimen has the lowest strength as compared to other direction specimens at all temperature conditions. With the increase in temperature above 600 °C, the material undergoes superplastic deformation with strain values reaches above 400% at 800˚C. In addition, an algorithm has been developed to determine the anisotropic parameters of Hill’s yield function as a function of temperature and equivalent plastic strain using the experimental data. The equivalent stress-strain curves considering anisotropy have also been evaluated as a function of temperature. These data shall be useful for design and safety analysis of the pressure tube for different types of postulated loading and accidental conditions.

17 July 2024 in Applied Mechanics
Verified
Journal Article
Open access
PDF file
Mahendra Kumar SamalMahendra Kumar Samal
Mahendra Kumar Samal
Trishant SahuTrishant Sahu
Trishant Sahu
ASAther Syed
Ather Syed
Aluminium alloys are used for the fabrication of the fuel clad of research-grade nuclear reactors as well as for several types of core components of high-flux research reactors. In order to carry out design and safety analysis of these components, their mechanical and fracture properties are required by the designer. In this work, experiments have been conducted on tensile specimens machined from an aluminium alloy block to evaluate the material stress-strain curve. Experiments have also been conducted on disc-shaped compact tension specimens in order to determine the fracture toughness of aluminium alloy. Numerical simulations of both tensile and fracture specimens have been carried out using the crystal plasticity model. Initially, the slip system level parameters of the crystal plasticity material model have been calibrated using experimental stress-strain data for single as well as polycrystalline aluminium. For the prediction of crack initiation toughness, Rice and Tracey’s damage model has been used. The critical damage parameter has been evaluated for a fractured specimen with a crack length-to-width (a/W) ratio of 0.6. The attainment of the critical damage parameter in the analysis corresponds to the instance of experimentally observed ductile crack initiation in the specimen. Later, this model was applied to other fracture specimens with different a/W ratios with values ranging from 0.39 to 0.59. It was observed that the critical damage parameter corresponding to crack initiation in the material has a very small variation, even if the specimens have different crack lengths. It is well-known in the literature that Rice and Tracey’s critical damage parameter is a material constant. Hence, we have applied the same model to predict crack initiation for single crystal fracture specimens with two different orientations of the crack plane. It was observed that the orientation is more susceptible to crack initiation and propagation compared with the orientation, as the damage parameter is high in the ligament of the specimen ahead of the crack tip for the same level of applied loading. As the [111] crack plane is more closely packed compared with the [100] plane, the distance between atomic planes is greater for the former, and hence, it is more susceptible to ductile damage. The results of the experiments and the material damage parameter are helpful for the integrity analysis of the fuel clad of research reactors as well as components of high-flux research reactors.

30 June 2025 in Preprints.org
Verified
Preprint
Open access
PDF file
ASAther Syed
Ather Syed
Mahendra Kumar SamalMahendra Kumar Samal
Mahendra Kumar Samal
The process of evaluation of mechanical properties of thin-walled small diameter tubes is cumbersome, especially, when the material exhibits significant anisotropy in the mechanical properties. For Zircaloy fuel clad tubes, the mechanical properties in the transverse or hoop direction are very different when compared to those along the length direction. As the diameter of the tubes is small, it is difficult to carry out conventional tensile tests and hence, ring tension tests are widely used. However, the ring tension test usually suffers from several drawbacks, such as the effect of friction between the ring and the loading mandrel on the stress-strain data and the existence of multi-axial state of stress in the gauge region. In this work, the effects of friction and state of stress have been taken into account in a new methodology, where the original load-displacement data is corrected for these effects using a correlation, which in turn has been derived from results of prior finite element analysis. The results of the new methodology have been validated by comparing data with those of conventional tensile tests. The new correlation has been used to evaluate transverse mechanical properties of Zircaloy-4 fuel clad over a wide temperature range, i.e., from 25oC to 900oC. This correlation has been used successfully for the first time in literature to evaluate the mechanical properties of Zircaloy-4 at such a high temperature environment. The data presented in this work is useful for safety analysts involved in simulation of severe accident progression and the correlation can be used to evaluate high temperature properties of similar thin-walled tubular components in industry.