Ioannis  Savidis

Prof. Ioannis Savidis

Integrated Circuits and Electronics (ICE) Design and Analysis Laboratory, Drexel University, Philadelphia, PA, USA

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 October 2012 in IEEE Journal of Solid-State Circuits
Verified
Journal Article
Closed access
ISIoannis Savidis
Ioannis Savidis
Selçuk KöseSelçuk Köse
Selçuk Köse
Eby FriedmanEby Friedman
Eby Friedman
A three-dimensional (3-D) test circuit examining power grid noise in a 3-D integrated stack has been designed, fabricated, and tested. Fabrication and vertical bonding were performed by MIT Lincoln Laboratory for a 150 nm, three metal layer SOI process. Three wafers are vertically bonded to form a 3-D stack. Noise analysis of three power delivery topologies is described. Calibration circuits for a source follower sense circuit compare the different power delivery topologies as well as the separate 3-D stacked circuits. The effect of the through silicon via (TSV) density on the noise profile of a 3-D power delivery network is experimentally described. A comparison of the peak noise for each topology with and without board level decoupling capacitors, and resonant behavior is provided, and suggestions for enhancing the design of a 3-D power delivery network are offered.

26 October 2021 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
Verified
Journal Article
Closed access
VRVaibhav Venugopal Rao
Vaibhav Venugopal Rao
ISIoannis Savidis
Ioannis Savidis
In this article, key-based obfuscation of the transistor dimensions is proposed to mask the biasing conditions of an analog circuit and, therefore, protect the circuit against intellectual property (IP) piracy. Vector- and mesh-based obfuscations are developed that provide different degrees of circuit security with tradeoffs in design complexity and area. An algorithm for the selection of an obfuscation transistor and a satisfiability modulo theory (SMT)-based algorithm that searches the design space to determine the dimensions of the obfuscation transistors are developed to reduce the computational complexity of designing and implementing the proposed parameter obfuscation techniques. The parameter obfuscation techniques, along with the developed algorithms, are implemented on an active inductor-based second-order bandpass filter (BPF) and an operational amplifier (op-amp). The results from the analysis of the obfuscated BPF and op-amp indicate that the critical circuit performances are properly locked with at least 15% variation from the target circuit parameters when setting incorrect transistor sizes. A simulation-based optimization algorithm is proposed to tune the biasing conditions and transistor body voltages, which mitigates the effects of both the parasitic impedance of the circuit and any variation due to the implementation of the obfuscation circuitry. The proposed simulation-based optimization algorithm determines the biasing conditions and body voltages of the BPF in 500 iterations and the op-amp circuit in 70 iterations, which provides a significant reduction in the design time and the number of circuit recycles. Implementing the parameter obfuscation technique with the proposed algorithms provides an efficient means to secure analog circuits while reducing the design time to implement security features.

12 May 2020 in IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems
Verified
Journal Article
Closed access
KJKyle Juretus
Kyle Juretus
ISIoannis Savidis
Ioannis Savidis

31 October 2014 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
Verified
Journal Article
Closed access
ISIoannis Savidis
Ioannis Savidis
BVBoris Vaisband
Boris Vaisband
Eby FriedmanEby Friedman
Eby Friedman
A 3-D test circuit examining thermal propagation within a through-silicon via-based 3-D integrated stack has been designed, fabricated, and tested. Design insight into thermal coupling in 3-D integrated circuits (ICs) through both experiment and simulation is provided, and suggestions to mitigate thermal effects in 3-D ICs are offered. Two wafers are vertically bonded to form a 3-D stack. Intraplane and interplane thermal coupling is investigated through single-point heat generation using resistive thermal heaters and temperature monitoring through four-point resistive measurements. Thermal paths are identified and analyzed based on the metric of thermal resistance per unit length. The peak steady-state temperature due to die location within a 3-D stack is described. The reduction in peak temperature through fan-based active cooling is also reported. Thermal propagation from a heat source located on the backside of the silicon is examined with both back metal and on-chip thermal sensors. A comparison of thermal coupling between two different heat sources on the same device plane is also provided.

17 April 2020 in IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems
Verified
Journal Article
Closed access
KJKyle Juretus
Kyle Juretus
ISIoannis Savidis
Ioannis Savidis
Current out-of-cone logic locking methodologies provide resiliency against the satisfiability (SAT) attack with minimal corruption when comparing the outputs of an activated and locked integrated circuit (IC). In addition, the structure of the modifications to the original logic leaks functional information of the circuit, which allows an adversary to determine the correct key. A novel logic locking methodology, CORruption Adaptable Logic Locking (CORALL), is introduced in this paper that provides increased security against the SAT attack for modified logic cones that require a large corruption of the primary outputs of the circuit, where the corruption is quantified by comparing between an activated and locked state of the IC. In addition, the modifications to the logic cone utilized by CORALL provide increased resilience against structural attacks. The CORALL architecture increases the number of iterations required to successfully execute a SAT attack for a flip function with 20 inputs by 34.41x over SFLL-HD n/4 and 82.36x over SFLL-Flex. In addition, a protected-cube selection process based on iterative-cofactors is introduced, which provides varying logical functions of the perturb unit and maps portions of the logic of the perturb unit into the look-up tables (LUTs) of the CORALL architecture. The variation in the logical functions implemented by the perturb unit and the mapped functionality of the perturb unit into a LUT provide resistance to all current structural attacks on out-of-cone logic locking techniques.

5 June 2017 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
Verified
Journal Article
Closed access
DPDivya Pathak
Divya Pathak
HHHouman Homayoun
Houman Homayoun
ISIoannis Savidis
Ioannis Savidis
In this paper, a dynamic on-chip power delivery system for chip multiprocessors (CMPs) is proposed, analogous to the smart grid deployed for large-scale energy distribution. The system includes underprovisioned on-chip voltage regulators (VRs) interconnected through a switch network. The peak current rating of the VRs is selected to meet only the average current demand of the cores. A real-time load-balancing algorithm is developed to reconfigure the power delivery network (PDN) by combining the output of multiple VRs when the workload demand exceeds the peak current rating of a single regulator. An operating system level task scheduling heuristic distributes the workloads on the cores such that the required reconfiguration of the PDN is minimized. Simulation results for the proposed power delivery system indicate up to a 44% reduction in the energy consumption of the CMP. In addition, the on-chip footprint of the PDN, including the on-chip VRs and the switching network, is reduced by at least 23%. The proposed cross-layer power management technique is an optimum solution for power-constrained many-core architectures implemented in advanced technology nodes.