Non-contact and full-field strain mapping captures strain across an entire surface, providing a complete two-dimensional (2D) strain distribution without attachment to sensors. It is an essential technique with wide-ranging applications across various industries, significantly contributing to experimental mechanics and structural health monitoring. Although there have been reviews that focus on specific methods, such as interferometric techniques or carbon nanotube-based strain sensors, a comprehensive comparison that evaluates these diverse methods together is lacking. This paper addresses this gap by focusing on strain mapping techniques specifically used in experimental mechanics and structural health monitoring. The fundamental principles of each method are illustrated with specific applications. Their performance characteristics are compared and analyzed to highlight strengths and limitations. The review concludes by discussing future challenges in strain mapping, providing insights into potential advancements and developments in this critical field.
22 December 2022 in Macromolecular Materials and Engineering
Graphene has proved to be an exceptional reinforcing additive for composites, but the high cost of its synthesis has largely prevented its addition on industrial scales. Flash Joule heating provides a rapid, bulk‐scale method for graphene synthesis from coal materials, such as metallurgical coke (MC), into metallurgical coke‐derived flash graphene (MCFG). Here, this work investigates the properties of graphene‐epoxy composites in a higher nanofiller content regime than has previously been reported in literature. Composites with 20 to 50 wt% loading of MCFG are prepared by combining MCFG with diglycidyl ether bisphenol A epoxy precursor (DGEBA) and 1,5‐diamino‐2‐methylpentane. With a 1:2 ratio of MCFG:DGEBA, the Young's modulus increases by 92% and with a 1:3 ratio, hardness increases by 140%. At a 1:4 ratio of MCFG:DGEBA, compressive strength and maximum strain increase by 145% and 61%, respectively. At a 1:3 ratio of MCFG:DGEBA, toughness increases by 496%. Finally, at a 1:1 ratio of MCFG:DGEBA, GHG emissions, water consumption, and energy consumption are reduced by 33%, 47%, and 34%, respectively. As the cost of FG plummets, since it can be produced from very low cost materials like MC, in milliseconds with no solvent or water, the prospects are promising for its high‐loading use in composites.
This study reports next generation optical strain measurement with “strain-sensing smart skin” (S4) and a comparison of its performance against the established digital image correlation (DIC) method. S4 measures strain-induced shifts in the emission wavelengths of single-wall carbon nanotubes embedded in a thin film on the specimen. The new S4 film improves spectral uniformity of the nanotube sensors, avoids the need for annealing at elevated temperatures, and allows for parallel DIC measurements. Noncontact strain maps measured with the S4 films and point-wise scanning were directly compared to those from DIC on acrylic, concrete, and aluminum test specimens, including one with subsurface damage. Strain features were more clearly revealed with S4 than with DIC. Finite element method simulations also showed closer agreement with S4 than with DIC results. These findings highlight the potential of S4 strain measurement technology as a promising alternative or complement to existing technologies, especially when accumulated strains must be detected in structures that are not under constant observation.
20 October 2023 in Macromolecular Materials and Engineering
CO2 emissions have become a significant environmental problem over the last few decades, often stemming from combustion of fossil fuels. Production and disposal of waste plastic also contribute greatly to greenhouse gas emissions, due to combustion of fossil fuels during manufacture and incineration or pyrolysis of the waste materials. Hence, researchers have begun developing technologies geared toward the capture, sequestration, and utilization of CO2. Several methods are shown to be useful for conversion of gaseous CO2 into solid carbon feedstocks, such as molten carbonate electrolysis. At the same time, flash Joule heating can rapidly and inexpensively convert carbon‐rich feedstocks into flash graphene (FG). Here, amorphous carbon derived from molten carbonate electrolysis of carbon dioxide is converted into FG, sometimes in combination with waste plastic, and demonstrated for use as a reinforcing additive in composite applications. FG can be used in epoxy and vinyl ester resins with a maximum increase in Young's modulus and hardness of 73% and 73%, respectively. Life cycle assessment also shows that adding 5 wt% 25:75 amorphous carbon‐derived FG to the epoxy results in 7.7%, 5%, and 2.7% decreases in CO2 emissions, water consumption, and energy consumption, respectively.
Structures in their service life are often damaged as a result of aging or extreme events such as earthquakes or storms. It is essential to detect damage in a timely fashion to ensure the safe operation of the structure. If left unchecked, subsurface damage (SSD) can cause significant internal damage and may result in premature structural failure. In this study, a Convolutional Neural Network (CNN) has been developed for SSD detection using surface strain measurements. The adopted network architecture is capable of pixel-level image segmentation, that is, it classifies each location of strain measurement as damaged or undamaged. The CNN which is fed full-field strain measurements as an input image of size 256 × 256 projects the SSD onto an output image of the same size. The data for network training is generated by numerical simulation of aluminum bars with different damage scenarios, including single damage and double damage cases at a random location, direction, length, and thickness. The trained network achieves an Intersection over Union (IoU) score of 0.790 for the validation set and 0.794 for the testing set. To check the applicability of the trained network on materials other than aluminum, testing is performed on a numerically generated steel dataset. The IoU score is 0.793, the same as the aluminum dataset, affirming the network’s capability to apply to materials exhibiting a similar stress–strain relationship. To check the generalization potential of the network, it is tested on triple damage cases; the IoU score is found to be 0.764, suggesting that the network works well for unseen damage patterns as well. The network was also found to provide accurate predictions for real experimental data obtained from Strain Sensing Smart Skin (S4). This proves the efficacy of the network to work in real-life scenarios utilizing the full potential of the novel full-field strain sensing methods such as S4. The performance of the proposed network affirms that it can be used as a non-destructive testing method for subsurface crack detection and localization.