Despite the widespread use of tunnel junctions in high-efficiency devices (e.g., multijunction solar cells, tunnel field effect transistors, and resonant tunneling diodes), simulating their behavior still remains a challenge. This paper presents a new model to complete that of Karlovsky and simulate an characteristic of an Esaki tunnel junction. A review of different analytical models of band-to-band tunneling models is first presented. As a complement to previous work on tunnel junction simulation, the transmission coefficient is precisely determined and incorporated, the valley current between the tunneling and drift regimes is included, and calculations of physical parameters are updated. It is found that the model works for a broad range of values of the forward bias.
Color management of integrated photovoltaics must meet two criteria of performance: provide maximum conversion efficiency and allow getting the chosen colors with an appropriate brightness, more particularly when using side by side solar cells of different colors. As the cooling conditions are not necessarily optimal, we need to take into account the influence of the heat transfer and temperature. In this article, we focus on the color space and brightness achieved by varying the antireflective properties of flat silicon solar cells. We demonstrate that taking into account the thermal effects allows freely choosing the color and adapting the brightness with a small impact on the conversion efficiency, except for dark blue solar cells. This behavior is especially true when heat exchange by convection is low. Our optical simulations show that the perceived color, for single layer ARC, is not varying with the position of the observer, whatever the chosen color. The use of a double layer ARC adds flexibility to tune the wanted color since the color space is greatly increased in the green and yellow directions. Last, choosing the accurate material allows both bright colors and high conversion efficiency at the same time.
Thin HIT solar cells combine efficient surface passivation and high open circuit voltage leading to high conversion efficiencies. They require a TCO layer in order to ease carriers transfer to the top surface fingers. This Transparent Conductive Oxide layer induces parasitic absorption in the low wavelength range of the solar spectrum that limits the maximum short circuit current. In case of thin film HIT solar cells, the front surface is patterned in order to increase the effective life time of photons in the active material, and the TCO layer is often deposited with a conformal way leading to additional material on the sidewalls of the patterns. In this article, we propose an alternative scheme with a local etching of both the TCO and the front a-Si:H layers in order to reduce the parasitic absorption. We study how the local resistivity of the TCO evolves as a function of the patterns, and demonstrate how the increase of the series resistance can be compensated in order to increase the conversion efficiency.
<!-- *** Custom HTML *** --> Many applications require colored surfaces while maximizing photons to pass through with no optical losses. As the perceived color depends on the spectral content and the number of reflected photons for each wavelength, it is necessary to consider not only the chromatic content but also the brightness. As a first application example, photovoltaic modules could see their acceptance in urban situations greatly improved if their color could be controlled while maximizing the number of photons used for energy conversion. In this case, it is important to limit light brightness to avoid glare when light coming from the sun is reflected directly. As another example, a colored and semi-transparent glass layer in the infrared could efficiently protect sensors while camouflaging them, such as lidar in automotive applications. We propose a theoretical study for multicolor applications, considering 2D partially etched grating waveguide structures that behave as a perfect broadband antireflection coating while the residual layer couples light in a waveguided mode in order to reflect only a particular photon band. This strategy allows to produce a large variety of colors and the use of non-absorbing materials avoids any optical loss. The width of the resonance peak is a crucial parameter for balancing brightness in multicolor applications. In the second part, we developed a method for a fast optimization of the geometrical parameters and we applied it to obtain the three primary colors with strong geometrical constraints, so that such structures could be manufactured in a single step by nano-imprint. Finally, we propose some improvements of these structures, in particular by reducing broadband reflection to obtain more saturated colors, or to improve the angular behavior of these structures.
The paper presents research focused on the efficiency improvement of inorganic flexible thin-film solar cells, using energy converting layers. The light capture enhancement was achieved through the introduction of layers based on rare-earth elements, as top coatings on the amorphous silicon photovoltaic structures. Such luminescent layers are converting high-energy photons into low-energy ones, which are more efficient in photovoltaic conversion of the investigated solar cells. Towards this goal, powders consisting rare-earth elements were applied as active particles in polymer layer. For practical experiments, the screen-printing method, as a cheap, reliable and industrially-ready technology was used for layers deposition. For the experiments two compositions were selected: Sr4Al14O25: Eu,Dy (BGL-300M) and SrAl2O4: Eu,Dy (G-300M). These materials are characterized by excellent thermal and optical stability and interesting luminescent properties (they absorb ultraviolet and emit in the visible range). For the verification of investigated materials and methods, various compositions of powders and proportions were tested and analyzed.