Alain Fave

Dr. Alain Fave

Univ. lyon
+3

Research Focus & Metrics

Academic Career Length

26Years (2001-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2004 in Thin Solid Films
Verified
Journal Article
Closed access
AFAlain Fave
Alain Fave
SQS. Quoizola
S. Quoizola
JKJ. Kraiem
J. Kraiem
AKA. Kaminski
A. Kaminski
MLM. Lemiti
M. Lemiti
ALA. Laugier
A. Laugier

25 April 2008
Verified
Conference Paper
Closed access
PDF file
CSChristian Seassal
Christian Seassal
YPYeonsang Park
Yeonsang Park
AFAlain Fave
Alain Fave
EDEmmanuel Drouard
Emmanuel Drouard
EFE Fourmond
E Fourmond
PVPierre Viktorovitch
Pierre Viktorovitch
A new concept of ultra-thin film photovoltaic solar cell including a planar photonic crystal is proposed. The goal is to couple the incident light into broad resonances guided in the absorbing layer. To achieve this, a periodic lattice is patterned within the active layer, for example made of holes in amorphous silicon. By adjusting the pattern dimensions, the spectral position and quality factor of these resonances can be controlled so as to optimise the global absorption. Design details will be discussed in this communication.

11 February 2021 in Nanomaterials
Verified
Journal Article
Open access
PDF file
Panus SundarapuraPanus Sundarapura
Panus Sundarapura
XZXiaomei Zhang
Xiaomei Zhang
RYRyoji Yogai
Ryoji Yogai
KMKazuki Murakami
Kazuki Murakami
AFAlain Fave
Alain Fave
MIManabu Ihara
Manabu Ihara
The photovoltaic effect in the anodic formation of silicon dioxide (SiO2) on porous silicon (PS) surfaces was investigated toward developing a potential passivation technique to achieve high efficiency nanostructured Si solar cells. The PS layers were prepared by electrochemical anodization in hydrofluoric acid (HF) containing electrolyte. An anodic SiO2 layer was formed on the PS surface via a bottom-up anodization mechanism in HCl/H2O solution at room temperature. The thickness of the oxide layer for surface passivation was precisely controlled by adjusting the anodizing current density and the passivation time, for optimal oxidation on the PS layer while maintaining its original nanostructure. HRTEM characterization of the microstructure of the PS layer confirms an atomic lattice matching at the PS/Si interface. The dependence of photovoltaic performance, series resistance, and shunt resistance on passivation time was examined. Due to sufficient passivation on the PS surface, a sample with anodization duration of 30 s achieved the best conversion efficiency of 10.7%. The external quantum efficiency (EQE) and internal quantum efficiency (IQE) indicate a significant decrease in reflectivity due to the PS anti-reflection property and indicate superior performance due to SiO2 surface passivation. In conclusion, the surface of PS solar cells could be successfully passivated by electrochemical anodization.

18 September 2018 in IEEE Journal of Photovoltaics
Verified
Journal Article
Closed access
PBPierre Bellanger
Pierre Bellanger
AMAlbert Minj
Albert Minj
AFAlain Fave
Alain Fave
ZDZakaria Djebbour
Zakaria Djebbour
SRStephane Roques
Stephane Roques
ASAbdelilah Slaoui
Abdelilah Slaoui
This work reports on the fabrication of silicon tunnel junctions that can be used in silicon-based bottom cells for tandem solar cells. The tunnel junction was formed on n-type monocrystalline silicon wafers using the following two different processes: 1) a thermal diffusion of boron followed by an arsenic ion implantation; and 2) successive implantation steps of boron and arsenic ions. For both the processes, a rapid thermal annealing step was used to activate the dopants and cure the defects generated by the ion implantation. The activated dopant distribution across the tunnel junction was determined by electrochemical capacitance–voltage (ECV) measurements. The quality of the device was assessed from the peak-to-valley ratio and peak current density of its current–voltage characteristics, as well as the resistivity. As a significant result, a peak current density value and a peak-to-valley ratio of approximately 50 A/cm2 and 1.7, respectively, were obtained for two consecutive implantations of boron and arsenic, followed by thermal annealing at 925 °C for 30 min. A very narrow depletion zone of 3.9 nm was calculated from the ECV dopant concentrations measurements under full depletion approximation. Finally, solar cells fabricated using this optimized process resulted in a conversion efficiency of 10.1% against 12% obtained from the reference monocrystalline solar cell.

16 January 2017 in EPJ Photovoltaics
Verified
Journal Article
Open access
RCRomain Champory
Romain Champory
FMFabien Mandorlo
Fabien Mandorlo
CSChristian Seassal
Christian Seassal
AFAlain Fave
Alain Fave
Thin HIT solar cells combine efficient surface passivation and high open circuit voltage leading to high conversion efficiencies. They require a TCO layer in order to ease carriers transfer to the top surface fingers. This Transparent Conductive Oxide layer induces parasitic absorption in the low wavelength range of the solar spectrum that limits the maximum short circuit current. In case of thin film HIT solar cells, the front surface is patterned in order to increase the effective life time of photons in the active material, and the TCO layer is often deposited with a conformal way leading to additional material on the sidewalls of the patterns. In this article, we propose an alternative scheme with a local etching of both the TCO and the front a-Si:H layers in order to reduce the parasitic absorption. We study how the local resistivity of the TCO evolves as a function of the patterns, and demonstrate how the increase of the series resistance can be compensated in order to increase the conversion efficiency.

20 February 2001 in Thin Solid Films
Verified
Journal Article
Closed access
AFAlain Fave
Alain Fave
SBS. Berger
S. Berger
ABA. Beaumont
A. Beaumont
BSB. Semmache
B. Semmache
PKP. Kleimann
P. Kleimann
ALA. Laugier
A. Laugier