Gerald A Miller

Dr. Gerald A Miller


Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2004 in Journal of Geotechnical and Geoenvironmental Engineering
Verified
Journal Article
Closed access
YLYong Yeow Lim
Yong Yeow Lim
GMGerald A Miller
Gerald A Miller
The wetting-induced compression of compacted Oklahoma soils was investigated. One-dimensional oedometer tests were conducted on 22 Oklahoma soils that encompassed relative compaction and moisture contents within typical embankment specifications. Results show that factors directly related to the fines composition can be used for preliminary estimation of collapse potential. Statistical analysis of the oedometer test data indicates that variables having the most impact on collapse index were compaction moisture content, dry unit weight, plasticity index, and clay-size fraction. Charts were developed to facilitate the estimation of collapse settlement of fills for different conditions, including fill height, moisture content, and soil type. Three case histories involving embankments that experienced significant settlement are presented for comparison. The comparison shows a reasonable agreement between predictions and field estimates of collapse settlement at the embankment centerlines; the limited evidence...

1 December 2016 in International Journal of Geomechanics
Verified
Journal Article
Closed access
MVMaryam Varsei
Maryam Varsei
GMGerald A Miller
Gerald A Miller
AHArash Hassanikhah
Arash Hassanikhah
Desiccation of soil is the gradual process of moisture loss from a fully or partially saturated condition to a dry state. If the soil is constrained against shrinkage during desiccation, it will begin to crack when tensile stresses in the soil exceed the tensile strength. Fundamental to understanding desiccation crack development in clayey soils is the accurate determination of the tensile strength during desiccation. Although numerous published studies have focused on soil desiccation and soil tensile strength, very little has been focused on experimental determination of tensile strength during desiccation. This paper presents the first generation of a novel apparatus designed to determine tensile strength during desiccation. During drying the tensile forces in a thin compacted soil layer are measured while simultaneously monitoring moisture content changes and crack formation via time-lapse photography. Results are presented from desiccation tests performed on two clayey compacted soils of medi...

12 March 2021 in Geotechnical Testing Journal
Verified
Journal Article
Closed access
KSKwestan Salimi
Kwestan Salimi
ACAmy Cerato
Amy Cerato
FVFarshid Vahedifard
Farshid Vahedifard
GMGerald A Miller
Gerald A Miller
The tensile strength of unsaturated soils is a critical factor controlling the initiation and propagation of desiccation cracks, which can threaten the structural integrity of natural and man-made earthen structures and slopes. Several engineering applications involve unsaturated soils subjected to elevated temperatures (e.g., earthen structure-atmospheric interaction under prolonged droughts, nuclear water disposal, energy piles, ground source heat pumps). Although the temperature dependency of desiccation cracking is demonstrated in the literature, critical gaps remain regarding the characterization of the tensile strength under elevated temperatures. The main objective of this study is to investigate the effect of elevated temperature on the tensile strength of unsaturated clays during desiccation. To accomplish this objective, a novel testing setup that can be used to directly determine soil tensile strength during desiccation was placed in an oven to measure the tensile strength of two compacted clayey soils of medium to high plasticity under different temperatures ranging from 20°C to 60°C. The clays are compacted at 95 % of their respective maximum dry unit weights over a range of water contents from dry to wet of optimum to investigate the influence of initial water content on tensile strength. The results demonstrated that the tensile strength decreased with increasing temperature. At the optimum water content, a tensile strength reduction of 36 % and 27 % in the highly plastic clay and the medium plastic clay, respectively, was observed when the temperature increased from 20°C to 60°C. Additionally, for the partially saturated condition, the initial water content affected the tensile strength significantly. Temperature-induced changes in key factors contributing to the tensile strength of unsaturated clays are discussed to provide further insight into tensile strength of clays at elevated temperatures. The findings of this study can contribute toward a more realistic analysis and design of earthen structures subjected to elevated temperatures.

1 November 2009 in Journal of Geotechnical and Geoenvironmental Engineering
Verified
Journal Article
Closed access
ACAmy Cerato
Amy Cerato
GMGerald A Miller
Gerald A Miller
JHJumanah A. Hajjat
Jumanah A. Hajjat
Volume changes due to wetting may occur in naturally deposited soils as well as earthen construction (e.g., compacted fills or embankments). Depending on the stress level, some soils exhibit increase in volume upon wetting (swell) while others may exhibit decrease in volume upon wetting (collapse). The work described in this paper focused on wetting-induced volume changes in compacted soils. Motivation for this work stemmed from observations of earthen structures that exhibit problematic behavior under wetting conditions, even though soils were compacted to engineering specifications (i.e., at or above minimum density and within moisture content ranges). Not only is this problematic behavior a concern but also the laboratory tests used to predict settlement of constructed facilities may not properly model the actual behavior of soil compacted under field conditions. For example, settlements experienced by compacted fills may be different from settlement predictions based on one-dimensional oedometer tests...

1 April 2016 in Journal of Geotechnical and Geoenvironmental Engineering
Verified
Journal Article
Closed access
ATAmirata Taghavi
Amirata Taghavi
KMKanthasamy K Muraleetharan
Kanthasamy K Muraleetharan
GMGerald A Miller
Gerald A Miller
ACAmy Cerato
Amy Cerato
A series of centrifuge tests were performed to investigate the behavior of laterally loaded pile groups in improved and unimproved soft clay. The soil profile consisted of four lightly overconsolidated clay layers overlying a dense layer of sand. The pile groups had a symmetrical layout consisting of 2×2 piles spaced at 3.0 and 7.0 pile diameters (D). After improving the soft clay in situ using simulated cement deep soil mixing (CDSM), pile foundations were driven into the improved ground. Centrifuge tests revealed that CDSM is an effective method to increase the lateral resistance of pile foundations. The lateral resistance of the improved pile group at 7D spacing increased by 157%. Due to pile–soil–pile interactions, the lateral resistance in the 3D pile group increased by only 112%. In both improved and unimproved pile groups with 3D spacing, the leading row of piles carried larger loads and bending moments than the trailing row of piles. No group interaction effects were observed in all pile g...

1 July 2021 in Journal of Geotechnical and Geoenvironmental Engineering
Verified
Journal Article
Closed access
PDF file
KSKwestan Salimi
Kwestan Salimi
ACAmy Cerato
Amy Cerato
FVFarshid Vahedifard
Farshid Vahedifard
GMGerald A Miller
Gerald A Miller
Characterization of tensile strength is critical to investigate the influence of desiccation and tensile cracks on the structural integrity of natural and artificial earthen structures and slopes. Although several models for the prediction of tensile strength of unsaturated soils have been proposed in the literature, critical gaps remain regarding a comprehensive model describing the tensile behavior of all soil types over a wide range of suction. This paper presents a general model for the tensile strength characteristic curve (TSCC) which establishes a relationship between the tensile strength versus water content in unsaturated soils. The proposed model is applicable to various soil types ranging from clean sands to silty and clayey soils. Tensile strength is characterized using the suction stress concept, and the TSCC model is built upon the concept that changes in tensile strength with water content (or degree of saturation) are primarily dominated by two distinct water retention mechanisms of capillarity and adsorption. Differences in the characteristics of capillary and adsorptive mechanisms and interparticle forces cause dissimilarities in the resultant TSCC in different soil types. Thus, a two-part suction stress characteristic curve (SSCC) was incorporated into the development of the TSCC to separately account for and distinguish interparticle forces and the resultant tensile strength under capillary and adsorptive mechanisms. The model was validated against laboratory-measured tensile strength reported in the literature for 10 soils, and was found to capture the tensile behavior of sandy, silty, and clayey soils well. Compared with several alternative models, the predictive accuracy of the proposed model was greater, particularly for clayey soils at low water contents (high suction). This superior performance can be attributed to properly accounting for the effect of adsorption mechanism, which is significant in clays.