This paper proposes an analytical approach predicting the development and progress of the plastic zone around a wellbore drilled in linear hardening or softening Drucker-Prager rocks in a theoretically consistent way. With some reasonable assumptions and simplifications on the definitions of stress invariants as well as the equivalent plastic strain, the wellbore boundary value problem is fully linearized, which leads to a simple ordinary differential equation with the radial displacement being the basic unknown. Explicit solutions for the stress and displacement fields due to wellbore drilling can thus be easily obtained. Comparisons between the analytical solution and the ABAQUS numerical simulation verify the reliability and applicability of the present closed-form solution. Extensive numerical results for the tangential and radial stress distributions are then provided to explore the influences of the friction angle and the plastic tangential modulus, for both strain hardening and softening ca...
1 June 2012 in International Journal of Geomechanics
Unsaturated soils are three-phase porous media consisting of a solid skeleton, pore water, and pore air. The behavior of unsaturated soils is strongly influenced by the matric suction (pore air pressure minus the pore water pressure). Soil water characteristic curves (SWCCs) describe the relationship between matric suction and water content in unsaturated soils and, therefore, capture the hydro-behavior of soils. SWCCs show hysteretic behavior that not only depends on the wetting or drying history of the soil, but also on the stress-strain history (mechanical behavior) of a soil. The hydro-behavior of unsaturated soils, on the other hand, influences the mechanical behavior through matric suction. To predict the behavior of unsaturated soils, a hysteretic SWCC model is proposed based on the bounding surface plasticity concept. The model for hysteretic SWCCs is then incorporated into a constitutive model for unsaturated sands and silts in the general stress space. The resulting model is a comprehens...
1 December 2016 in International Journal of Geomechanics
Recent laboratory tests and field observations have revealed that unsaturated sands are susceptible to liquefaction. Systematic investigation of liquefaction potential of unsaturated sands is, however, lacking. In this paper, a coupled hydromechanical elastoplastic constitutive model for unsaturated sands is calibrated using available laboratory test results. A parametric study is then conducted using the calibrated constitutive model to investigate the effects of initial degree of saturation, relative density, and effective confining pressure on the liquefaction resistance of unsaturated sands. The results suggest that the liquefaction resistance of unsaturated sands increases with decreasing degree of saturation and increasing relative density and effective confining pressure. The results also reveal that the effect of degree of saturation on liquefaction resistance is more pronounced near 100% degree of saturation. The results of the parametric study are then condensed to create a design chart...
1 April 2016 in Journal of Geotechnical and Geoenvironmental Engineering
A series of centrifuge tests were performed to investigate the behavior of laterally loaded pile groups in improved and unimproved soft clay. The soil profile consisted of four lightly overconsolidated clay layers overlying a dense layer of sand. The pile groups had a symmetrical layout consisting of 2×2 piles spaced at 3.0 and 7.0 pile diameters (D). After improving the soft clay in situ using simulated cement deep soil mixing (CDSM), pile foundations were driven into the improved ground. Centrifuge tests revealed that CDSM is an effective method to increase the lateral resistance of pile foundations. The lateral resistance of the improved pile group at 7D spacing increased by 157%. Due to pile–soil–pile interactions, the lateral resistance in the 3D pile group increased by only 112%. In both improved and unimproved pile groups with 3D spacing, the leading row of piles carried larger loads and bending moments than the trailing row of piles. No group interaction effects were observed in all pile g...
1 June 2012 in International Journal of Geomechanics
Following the comprehensive model formulation given in Part I, a fully implicit integration procedure for the rate equations using a closest point projection method is presented in this paper. The stress-update algorithm and calibration procedure for all the model parameters are discussed in detail. Two sets of laboratory test results, one from unsaturated Minco silt and another one from Toyoura sand, are used to validate the proposed model. The model is shown to have the ability to capture the coupling effects between hydro- and mechanical behavior and predict the laboratory tests reasonably well.