Residual stresses and surface roughness have been recognized to play a critical role in the fatigue strength of metal components. Machining processes can induce different roughness and residual stress conditions depending on the parameters used in the process. Therefore, it is essential to develop knowledge that helps to predict the residual stresses and roughness that would be obtained from different machining conditions. Due to the growing interest from the industry in the use of 42CrMo4 steel because of its excellent mechanical properties, the main objective of this work is to establish two phenomenological models to accurately predict the residual stress and roughness values in turned specimens of this material. The models are derived from data of four process variables: (a) insert tip radius; (b) feed rate; (c) cutting speed; and (d) depth of cut. For this purpose, a wide experimental campaign has been developed, which includes the machining of 68 specimens under various cutting scenarios, and their subsequent measurement of residual stresses and roughness. Once the experimental data were obtained, the response surface method based on the central composite design was used to fit the models, obtaining a correlation index $${R}^{2}$$ higher than 0.9 in both cases. In this article, it is concluded that feed rate and insert radius have a greater effect on the residual stress and roughness obtained, while cutting speed and depth of cut have a lesser impact on the results. It is hoped that the findings will establish a groundwork for the machining of this material type, ensuring controlled conditions of residual stress and roughness.
The turning process remains one of the most widely used manufacturing methods in the industry due to its high flexibility and production rates. Despite being an extensively used technique, the impact of this machining process on the surface integrity of the components has not yet been resolved in the literature, although it is well known that it can have a major influence on their final life. With the aim of providing new insights in the field, an extensive experimental campaign was designed on a 42CrMo4 quenched and tempered steel (in the following 42CrMo4+QT) using the response surface method. As inputs of this experimental design, the principal machining parameters were selected: feed rate (mm/rev), cutting speed (m/min), depth of cut (mm) and insert radius (mm). Meanwhile the main outputs measured where the surface roughness (µm) and the longitudinal residual stresses (MPa). In parallel, the turning operation of each specimen was monitored and the forces (X, Y and Z), current consumption of the main lathe motor, sound pressure and tool holder accelerations were recorded.
The ongoing large-scale deployment of renewable energy technologies aimed at reducing dependence on fossil fuels has led to the widespread use of structural details that are not explicitly covered by current fatigue design standards, posing significant challenges for their reliable assessment. Among them, preloaded slotted bolted joints are commonly adopted in solar tracker structures owing to their capability to accommodate assembly tolerances and on-site misalignments. Although these joints are typically designed according to a slip-resistant philosophy, their fatigue performance under cyclic loading below their slip load has not yet been addressed in the specialized literature. To address this gap, the present study investigates several joint configurations representative of solar tracker connections under static and fatigue loading, considering different levels of bolt preload. A combined experimental and numerical approach was adopted, in which static tests were first used to determine the slip resistance of the joints, and subsequently, their fatigue behavior was analyzed under load levels deliberately selected to be below their slip failure. In parallel, detailed finite element models were developed, and fatigue life predictions were performed using different local strain-based and multiaxial fatigue approaches. The results demonstrate strong agreement between numerical predictions and experimental observations, indicating that preloaded bolted connections with slotted holes, commonly employed in solar structures, do not exhibit fatigue damage when subjected to loads below their slip resistance, with fatigue lives exceeding the investigated cycle range.
6 November 2026 in Computer Applications in Engineering Education
This paper presents a transferable computer‐aided engineering educational framework for teaching topology optimization through polymer material extrusion prototyping and numerical‐experimental validation. The framework is intended to help students move from idealized numerical simulation toward design decisions constrained by manufacturability, physical testing and failure interpretation. It is organized as a compact six‐stage workflow: material characterization and calibration, baseline structural simulation, topology optimization and verification, computer‐aided design reconstruction and design for additive manufacturing, controlled prototyping, and physical testing with redesign where needed. Its feasibility was examined through a master‐level implementation in which five student teams, distributed across two course editions, optimized and tested a pin‐loaded polymer component required to withstand 500 N. The implementation provides descriptive, team‐level evidence of technical feasibility and educational traceability. Student reports and prototypes documented material calibration, manufacturable reconstruction of topology‐optimization outputs, and experimental validation of final designs. All reported final designs exceeded the 500 N requirement, with measured final masses between 14.25 and 19.55 g and experimental failure loads between 740 and 1300 N. The tests also revealed bending and buckling in slender optimized members, showing that stress‐based topology optimization must be complemented with stability checks and physical validation. The study contributes a reproducible educational framework that closes the design‐simulate‐optimize‐manufacture‐test cycle within a compact laboratory structure.
7 September 2026 in Journal of Constructional Steel Research