Stéphane GILLE

Dr. Stéphane GILLE

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 March 2025 in Safety
Verified
Journal Article
Open access
PDF file
SGStéphane GILLE
Stéphane GILLE
Design standards for manual handling equipment tend to measure maximal loads and moving forces using a smooth, flat, horizontal steel plate; yet, in everyday use, such equipment is used on floor coverings. Such test methods therefore overestimate the maximal loads acceptable for operators, which increases the risk of injury including the development of musculoskeletal disorders. This study presents a new approach for calculating the pushing force for manually handled equipment moving longitudinally on resilient floor coverings from the pushing force measured on a steel plate. This method combines corrective forces with the pushing force model presented in this study. Corrective force abaci, which describe corrective forces as functions of the hardness of the floor covering’s base foam, are provided for each type of tread and bearing in the cart’s wheels. These abaci have been elaborated from pushing force measurements obtained with 44 wheel designs (of varying diameters, treads and bearings) tested on five different floors on a custom-built test bench. A mean deviation between experimental results and model predictions of 5.1% is obtained for pushing forces. These results permit us to account for the real conditions in which manual handling equipment is used and help in reducing the incidence of musculoskeletal disorders.

2 August 2024 in Safety
Verified
Journal Article
Open access
PDF file
SGStéphane GILLE
Stéphane GILLE
ICIsabelle Clerc-Urmès
Isabelle Clerc-Urmès
Test methods that use pushing forces to evaluate the maximal load capacities of carts in design standards require a flat, smooth and horizontal steel plate and thus do not take into account the real conditions of work. Resistive forces of a single wheel of a cart in a uniform rectilinear motion were measured using a unique test bench with five loads. Forty-four wheels were tested (varying diameters, treads and bearings) with one steel plate and four resilient floor coverings. Based on a linear mixed model, all the following results were significant (p < 0.05). Resistive forces were increased linearly with the load and depended on the characteristics of both the wheel and floor. These forces decreased as the diameter increased. They were important for wheels with sleeve bearings but decreased for cone ball bearings and precision ball bearings. Resistive forces depended on the material of the tread and were higher for solid rubber treads. In contrast, the hardness of the tread had little effect. Resistive forces strongly depended on the hardness of the base foam of resilient floor coverings: the softer the base foam, the higher the resistive forces. Test methods in design standards should be reviewed, using corrective forces based on these present results, to prevent musculoskeletal disorders.

18 August 2026 in Safety
Verified
Journal Article
Open access
PDF file
SGStéphane GILLE
Stéphane GILLE
AKAlexandre Klingler
Alexandre Klingler
This study presents the design, theoretical modeling, and experimental validation of a novel mechanical reducer made up of three stages, including two logarithmic spiral gears, offering a continuously variable transmission ratio. Unlike conventional constant transmission ratio reducers (circular gears reducers), this reducer provides high transmission ratios during motion initiation and gradually decreases them per cycle, preventing abrupt torque transition. A comprehensive mechanical model was developed to predict transmission ratio, gear geometry, assistance distance and duration, motor torque, and energy consumption, providing a complete framework for reducer design according to target performance requirements. A proof-of-concept prototype manufactured by additive manufacturing was integrated into a trolley to validate the mechanical model. Experimental results demonstrated good agreement with theoretical predictions, with no difference in distance crossed and 13% difference in assistance duration. The model further predicts substantially lower energy consumption than conventional reducers, while maintaining progressive torque delivery throughout the assistance phase. These results demonstrate the potential of logarithmic spiral gears for variable-ratio mechanical transmissions and provide a predictive framework for the design and optimization of this type of mechanism. This reducer is hypothetically intended for applications requiring progressive torque assistance, such as manual trolleys, wheelchairs, or aircraft.