The Educational Irish Research Satellite (EIRSAT-1) is a 2U CubeSat developed at University College Dublin. The project aims to build, test, launch, and operate Ireland’s first satellite and to perform in-orbit demonstrations of three novel payloads developed in-house. To reduce risk within the mission, the project employs a prototype model philosophy in which two models of the spacecraft exist: an engineering qualification model (EQM) and a flight model (FM). This paper presents the verification approach of the functional tests implemented for the EIRSAT-1 project. The activities of the FlatSat and system level full functional tests of the EQM are presented and the results obtained during the test campaigns are discussed. Four test anomalies were encountered during the full functional test campaign resulting in two minor redesigns, and subsequent reassembly, of the CubeSat. The functional test campaigns highlighted the importance of FlatSat level testing of CubeSats to ensure compatibility of all subsystems prior to assembly and of thorough documentation to diagnose any unexpected behaviour of the hardware efficiently. The functional verification of the EQM proved that the system conformed to its design, verifying 57 mission requirements, and is a crucial step towards the development of the EIRSAT-1 FM.
CubeSats facilitate rapid development and deployment of missions for educational, technology demonstration, and scientific purposes. However, they are subject to a high failure rate, with a leading cause being the lack of system-level verification. The Educational Irish Research Satellite (EIRSAT-1) is a CubeSat mission under development in the European Space Agency’s (ESA) Fly Your Satellite! Programme. EIRSAT-1 is a 2U CubeSat with three novel payloads and a bespoke antenna deployment module, which all contribute to the complexity of the project. To increase the likelihood of mission success, a prototype model philosophy is being employed, where both an engineering qualification model (EQM) and a flight model of EIRSAT-1 are being built. Following the assembly of the EQM, the spacecraft underwent a successful full functional test and month-long mission test. An environmental test campaign in ESA Education Office’s CubeSat Support Facility was then conducted with the EQM where both vibration and thermal verification test campaigns were performed. The focus of this paper is the thermal testing and verification of the EIRSAT-1 EQM. Over three weeks, the EQM was subjected to one non-operational cycle, three and a half operational cycles, and a thermal balance test in a thermal vacuum chamber. After dwelling at each temperature extreme, functional tests were performed to investigate the performance of the spacecraft in this space representative environment. The approach to planning and executing the thermal testing is described in detail including the documentation required, set up of the test equipment, and determination of the test levels. Overall, the campaign demonstrated that the mission can successfully operate in a space environment similar to that expected in orbit, despite encountering a number of issues. These issues included a payload displaying anomalous behaviour at cold temperatures and needing to redefine test levels due to an insufficient understanding of the internal dissipation in the spacecraft. A total of two major and three minor non-conformances were raised. Crucially, these issues could not have been found without thermal testing, despite the comprehensive ambient tests performed. The main results and lessons learned during this thermal test campaign are presented with the aim of guiding future missions on optimal approaches in organising and executing the thermal testing of their CubeSats.
28 November 2017 in Journal of Astronomical Telescopes, Instruments, and Systems
E-ASTROGAM is a gamma-ray space mission proposed for the fifth medium-size mission (M5) of the European Space Agency. It is dedicated to the study of the nonthermal universe in the photon energy range from ∼0.15 MeV to 3 GeV with unprecedented sensitivity and angular and energy resolution, together with a ground-breaking capability for gamma-ray polarimetric measurements over its entire bandwidth. We discuss here the main polarization results expected at low energies, between 150 keV and 5 MeV, using Compton interactions in the e-ASTROGAM instrument, from observations of active galactic nuclei, gamma-ray bursts, microquasars, and the Crab Pulsar and Nebula. The anticipated performance of the proposed observatory for polarimetry is illustrated by simulations of the polarization signals expected from various sources. We show that polarimetric analyses with e-ASTROGAM should provide definitive insight into the geometry, magnetization, and content of the high-energy plasmas found in the emitting sources, as well as on the processes of radiation of these plasmas.
1 January 2023 in Journal of Astronomical Telescopes, Instruments, and Systems
The capabilities of CubeSats have grown significantly since the first of these small satellites was launched in the early 2000s. These capabilities enable a wide range of mission profiles, with CubeSats emerging as viable platforms for certain space-based astronomical research applications. The Educational Irish Research Satellite (EIRSAT-1) is a CubeSat being developed as part of the European Space Agency’s Fly Your Satellite! program. In addition to its educational aims, the mission is driven by several scientific and technological goals, including goals related to a novel gamma-ray instrument for the detection of bright transient astrophysical sources, such as gamma-ray bursts. This work provides a detailed description of the software development life-cycle for EIRSAT-1, addressing the design, development and testing of robust flight software, aspects of payload interfacing, and risk mitigation. The described design-to-testing approach was implemented to establish, prior to launch, that EIRSAT-1 can perform its intended mission. Constraints and challenges typically experienced by CubeSat teams, which can impact the likelihood of mission success, are considered throughout this work, and lessons learned are discussed. The aim of this work is to highlight the advanced capabilities of CubeSats while providing a useful resource for teams implementing their own flight software.
The compact, standardised form factor of CubeSats allows for the use of commercial off-the-shelf components, reducing traditional barriers to entry, such as cost and development time. More than 1500 of these small spacecraft have been launched in the past 20 years, with improving capabilities that enable a wide range of mission profiles. The Educational Irish Research Satellite, EIRSAT-1, is a CubeSat being developed by a student-led team with goals that span education, technology demonstration and science. A comprehensive mission test plan, in which in-flight conditions are simulated, has been developed for EIRSAT-1 and implemented using an engineering qualification model of the spacecraft. In addition to verifying 41 mission requirements, the successful execution of the mission test plan established that the full satellite system can perform the intended mission. Mission testing also proved to be an invaluable tool to prepare for launch and operations, providing the team with a more complete understanding of the satellite’s expected on-orbit behaviour. This work presents a detailed description of the mission test planning process and implementation, as well as key results and lessons learned. In doing so, this work aims to improve the on-orbit reliability of CubeSats by disseminating resources and good practice around mission testing.
1 July 2023 in Journal of Astronomical Telescopes, Instruments, and Systems
CubeSats provide opportunities for science and technology demonstration missions with low-cost solutions and short project timescales, in particular, for studying gamma-ray bursts (GRBs) in the multi-messenger era. A robust operations strategy for scientific CubeSat projects is key to optimizing the results obtained from the experimental instruments. The Educational Irish Research Satellite-1 (EIRSAT-1) is a 2U CubeSat with three payloads, including a bespoke gamma-ray detector, gamma-ray module (GMOD), developed in-house for the detection of GRBs. The detection and reporting of GRB triggers to the scientific community complicates and drives the mission operational strategy. The operational procedures developed for commissioning and operating GMOD are detailed. The successful operation of EIRSAT-1 will facilitate the detection of ∼15 GRBs / year in low Earth orbit. To increase the likelihood of mission success, the project is following a prototype model philosophy, building, and testing, both an engineering qualification model (EQM) and flight model. The EIRSAT-1 operations manual is the document that will instruct operators in commanding the spacecraft correctly and efficiently throughout the mission lifetime. The operations manual must be refined in parallel to payload development. This two-model philosophy has provided time for the early development of the EIRSAT-1 operations manual with the EQM. The EIRSAT-1 operations manual has undergone incremental updates based on feedback from operational development tests (ODTs), and a version with 35 procedures was frozen prior to the month-long EQM mission test (MT). Specifically, the objective of our work is to validate and refine the operations manual using the EQM MT process. Although the ODTs were effective preparation, the MT process highlighted issues, such as procedures operators found convoluted, and scenarios not yet considered during the initial development stages. Two new procedures were identified, 8 procedures required major updates, 15 required minor updates, and the remaining 12 required no improvements after the MT. The validation process facilitated operator training in mission representative conditions, such as GRB triggering data downlink with GMOD, and the major lessons learned during the development and validation process are presented.