HENRY IKENNA IDU

Mr. HENRY IKENNA IDU

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 February 2025 in Energies
Verified
Journal Article
Open access
PDF file
Yerassyl OlzhabayYerassyl Olzhabay
Yerassyl Olzhabay
HENRY IKENNA IDUHENRY IKENNA IDU
HENRY IKENNA IDU
MHMuhammad Najwan Hamidi
Muhammad Najwan Hamidi
DIDahaman Ishak
Dahaman Ishak
AMArjuna Marzuki
Arjuna Marzuki
IUIkechi A. Ukaegbu
Ikechi A. Ukaegbu
The rapid rise in the power conversion efficiency (PCE) of perovskite solar cells (PSCs) has opened the door for diverse potential applications in powering indoor Internet of Things (IoT) devices. An energy harvesting system (EHS) powered by a PSC module with a backup Li-ion battery, which stores excess power at moments of high irradiances and delivers the stored power to drive the load during operation scenarios with low irradiances, has been designed. A DC-DC boost converter is engaged to match the voltage of the PSC and Li-ion battery, and maximum power point tracking (MPPT) is achieved by a perturb and observe (P&O) algorithm, which perturbs the photovoltaic (PV) system by adjusting its operating voltage and observing the difference in the output power of the PSC. Furthermore, the charging and discharging rate of the battery storage is controlled by a DC-DC buck–boost bidirectional converter with the incorporation of a proportional–integral (PI) controller. The bidirectional DC-DC converter operates in a dual mode, achieved through the anti-parallel connection of a conventional buck and boost converter. The proposed EHS utilizes DC-DC converters, MPPT algorithms, and PI control schemes. Three different case scenarios are modeled to investigate the system’s behavior under varying irradiances of 200 W/m2, 100 W/m2, and 50 W/m2. For all three cases with different irradiances, MPPT achieves tracking efficiencies of more than 95%. The laboratory-fabricated PSC operated at MPP can produce an output power ranging from 21.37 mW (50 W/m2) to 90.15 mW (200 W/m2). The range of the converter’s output power is between 5.117 mW and 63.78 mW. This power range can sufficiently meet the demands of modern low-energy IoT devices. Moreover, fully charged and fully discharged battery scenarios were simulated to study the performance of the system. Finally, the IoT load profile was simulated to confirm the potential of the proposed energy harvesting system in self-sustainable IoT applications. Upon review of the current literature, there are limited studies demonstrating a combination of EHS with PSCs as an indoor power source for IoT applications, along with a bidirectional DC-DC buck–boost converter to manage battery charging and discharging. The evaluation of the system performance presented in this work provides important guidance for the development and optimization of new-generation PV technologies like PSCs for practical indoor applications.

7 July 2024 in Nanomaterials
Verified
Journal Article
Open access
PDF file
DADamir Aidarkhanov
Damir Aidarkhanov
HENRY IKENNA IDUHENRY IKENNA IDU
HENRY IKENNA IDU
XZXianfang Zhou
Xianfang Zhou
DDDawei Duan
Dawei Duan
FWFei Wang
Fei Wang
Annie NgAnnie Ng
Annie Ng
As one of the most promising photovoltaic technologies, perovskite solar cells (PSCs) exhibit high absorption coefficients, tunable bandgaps, large carrier mobilities, and versatile fabrication techniques. Nevertheless, the commercialization of the technology is hindered by poor material stability, short device lifetimes and the scalability of fabrication techniques. To address these technological drawbacks, various strategies have been explored, with one particularly promising approach involving the formation of a low-dimensional layer on the surface of the three-dimensional perovskite film. In this work, we demonstrate the use of guanidinium tetrafluoroborate, CH6BF4N3, (GATFB) as a post-treatment step to enhance the performance of PSCs. Compared with the control sample, the application of GATFB improves the film surface topology, reduces surface defects, suppresses non-radiative recombination, and optimizes band alignment within the device. These positive effects reduce recombination losses and enhance charge transport in the device, resulting in PSCs with an open-circuit voltage (VOC) of 1.18 V and a power conversion efficiency (PCE) of 19.7%. The results obtained in this work exhibit the potential of integrating low-dimensional structures in PSCs as an effective approach to enhance the overall device performance, providing useful information for further advancement in this rapidly evolving field of photovoltaic technology.